manualshive.com logo in svg

Thermo Scientific AQUAfast AQ3700, User Manual

The Thermo Scientific AQUAfast AQ3700, a cutting-edge device incorporating advanced technology, guarantees accurate and swift measurements. Enhance your experience by accessing the comprehensive and user-friendly User Manual, available for free download on our website. Maximize your product's potential with step-by-step instructions and detailed specifications.

Share
Download
background image

7

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

1.1 Methods

Cyanuric acid 

with Tablet

0 – 160 mg/l CyA

1.   Fill a clean vial (24 mm Ø) with 

5 ml of the water  

 

sample

 and 

5 ml deionized water (Note 1)

, close  

 

tightly with the cap. 

2.   Place the vial in the sample chamber making sure that 
 

the   marks are aligned.

3.   Press 

ZERO

 key.

4.   Remove the vial from the sample chamber.

5.   Add 

one CyA - TEST tablet 

straight from the foil  

 

to the prepared water sample and crush the  

 

tablet using a clean stirring rod.

6.   Close the vial tightly with the cap and swirl several times  
 

until the tablet is dissolved (Note 2, 3).

7.   Place the vial in the sample chamber making sure that 
 

the   marks are aligned.

8.   Press 

TEST

 key.

 

The result is shown in the display in mg/l Cyanuric acid. 

 prepare Zero
 press ZERO

 Zero accepted
 prepare Test
 press TEST

6

0

1

Summary of Contents for AQUAfast AQ3700









































































































































































































































































Reviews:

No comments

Related manuals for AQUAfast AQ3700

Oldham BM25 Operating Manual preview
BM25
Brand: Oldham Pages: 43
Macnaught MH450 Manual preview
MH450
Brand: Macnaught Pages: 4
VEE GEE BX-2 Operation Manual preview
BX-2
Brand: VEE GEE Pages: 2
T&D TR7 Series Introductory Manual preview
TR7 Series
Brand: T&D Pages: 2
T&D TR7 Series Quick Start Manual preview
TR7 Series
Brand: T&D Pages: 2
UE Systems Ultraprobe 9000 Manual preview
Ultraprobe 9000
Brand: UE Systems Pages: 25
UE Systems ULTRAPROBE 10000 General Setup And Knowledge preview
ULTRAPROBE 10000
Brand: UE Systems Pages: 6
Cecomp F20B Instruction Manual preview
F20B
Brand: Cecomp Pages: 4
E+E Elektronik EE772 User Manual preview
EE772
Brand: E+E Elektronik Pages: 32
LEGRAND LG-41492 Quick Start Manual preview
LG-41492
Brand: LEGRAND Pages: 5
Kawai Digital Piano CA750 Owner'S Manual preview
Digital Piano CA750
Brand: Kawai Pages: 76
Toro Turf Guard Installation Setup Manual preview
Turf Guard
Brand: Toro Pages: 60
Velleman NETBSEM User Manual preview
NETBSEM
Brand: Velleman Pages: 15
Konica Minolta CM-3700A Instruction Manual preview
CM-3700A
Brand: Konica Minolta Pages: 42
Kobold KSK Operating Instructions Manual preview
KSK
Brand: Kobold Pages: 12
S+S Regeltechnik RHEASREG KLSW-3 Operating Instructions, Mounting & Installation preview
RHEASREG KLSW-3
Brand: S+S Regeltechnik Pages: 32
D-tect Systems MiniRad-DX Installation And Operating Instructions Manual preview
MiniRad-DX
Brand: D-tect Systems Pages: 28
BERG UBN204 Standard Protocol Manual preview
UBN204
Brand: BERG Pages: 23

Brands by name

Popular brands

Load more brands