Thermo Scientific AQUAfast AQ3700 User Manual Download

Page: 62 / 264

Thermo Scientific Orion AQUAfast AQ3700 Colorimeter User Guide

1.1 Methods

Chlorine HR (Kl)

with Tablet

5 – 200 mg/l Cl

Insert the adapter for 16 mm Ø vials.

1. Fill a clean vial (16 mm Ø) with

8 ml of the water

sample

, close tightly with the cap.

2. Place the vial in the sample chamber making sure that

the marks are

aligned.

3. Press

ZERO

key.

4. Remove the vial from the sample chamber.

5. Add

one CHLORINE HR (KI) tablet

straight from

the foil to the water sample and crush the tablet using

a clean stirring rod.

6. Add

one ACIDIFYING GP tablet

straight from the

foil to the same water sample and crush the tablet using a

clean stirring rod.

7. Close the vial tightly with the cap and swirl several times

until the tablets are dissolved.

8. Place the vial in the sample chamber making sure

that the marks are

aligned.

9. Press

TEST

key.

The result is shown in the display in mg/l Chlorine.

prepare Zero
press ZERO

Zero accepted
prepare Test
press TEST

Ø 16 mm

Summary of Contents for AQUAfast AQ3700









































































































































































































































































Search results

Summary of Contents for AQUAfast AQ3700

Reviews:

Related manuals for AQUAfast AQ3700

Brands by name

Popular brands

Thermo Scientific AQUAfast AQ3700, User Manual

Search results

Summary of Contents for AQUAfast AQ3700

Reviews:

Related manuals for AQUAfast AQ3700

Brands by name

Popular brands