Telex Azedit Software Manual Download Page 78 | Manualshive

Page: 78 / 182

background image

Telex Communications

78

GPI Out

ADAM and ADAM CS intercom systems have a General Purpose Interface (GPI) port. GPI ports have eight control
outputs (also referred to as relays) and eight control inputs. The location of the GPI port on the ADAM and ADAM CS
is as follows:

ADAM:

Located on XCP-ADAM-MC Master Controller Breakout Panel, J11.

ADAM CS: Located on ADAM CS back panel, J903.

GPI Port Pin-out

All 25-pin GPI Port connectors have the same pin-out as follows:

Pin No. Function:

1. GPI In #1 (+5 to +18 VDC)

2. GPI In #2 (+5 to +18 VDC)

3. GPI In #3 (+5 to +18 VDC)

4. GPI In #4 (+5 to +18 VDC)

5. GPI In #5 (+5 to +18 VDC)

6. GPI In #6 (+5 to +18 VDC)

7. GPI In #7 (+5 to +18 VDC)

8. GPI In #8 (+5 to +18 VDC)

9. Common

10. Common

11. Common

12. Common

13. Common

14. GPI Out #1

15. GPI Out #2

16. GPI Out #3

17. GPI Out #4

18. GPI Out #5

19. GPI Out #6

20. GPI Out #7

21. GPI Out #

22. Common

23. Common

24. Common

25. Common

GPI Inputs for UIO-256, ADAM, and ADAM CS: C5 to +18 VDC between any GPI input and common to
activate that GPI input.

GPI outputs UIO-256: Activating a GPI output causes a relay contact closure between that output and common. The
relay contacts are rated for 0.5A at 120 VAC; 1A at 24 VDC; 0.3A at 60 VDC.

GPI Outputs for ADAM and ADAM CS: Activating a GPI output causes an active high output. This can be changed
to active low by going to the Options menu and selecting Intercom Configuration (on the Options sheet, select the
Configure onboard GPI Outputs in FR9528 mode).

GPI Outputs

Also, referred to as Relays, GPI Outputs can be used to activate external devices directly from keypanel keys. For
example, an external lighting control device can be activated from a keypanel key. A GPI Output can also be set up to
activate when a person talks to a certain port. For example, connect a 2-way radio to an intercom port and then set
up a GPI output to activate whenever anyone talks into the transmitter. GPI Outputs can also be used to activate

«
...
76
77
78
79
80
...
»

Summary of Contents for Azedit























































































































































































Reviews:

No comments

Related manuals for Azedit

PT-D10000 Series

Brand: Panasonic Pages: 37

MAGICTWINXP-R10

Brand: JETWAY Pages: 43

Brand: Olympus Pages: 149

Brand: I-Data Pages: 79

SENTINEL LOG MANAGER 1.0.0.5 - 03-31-2010

Brand: Novell Pages: 168

COLDFUSION 5 - INSTALING AND CONFIGURING...

Brand: MACROMEDIA Pages: 160

BlackArmor WS 110

Brand: Seagate Pages: 2

Brand: FARONICS Pages: 4

WINSELECT STANDARD

Brand: FARONICS Pages: 36

IRISPowerscan 9.5

Brand: I.R.I.S. Pages: 182

Brand: Silicon Image Pages: 36

ITANIUM ARCHITECTURE - SOFTWARE DEVELOPERS VOLUME 3 REV 2.3

Brand: Intel Pages: 1898

Brand: Nikon Pages: 38

Trillium Lane Labs

Brand: DigiDesign Pages: 114

00128-051462-9310 - AUTOCAD 2008 COMM UPG FRM 2005 DVD

Brand: Autodesk Pages: 2268

AUTOCAD P AND ID 2010

Brand: Autodesk Pages: 4

657B1-000110-S001 - Maya - Mac

Brand: Autodesk Pages: 5

131018 - StorView Snapshot - Mac

Brand: LaCie Pages: 214

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands