Telex Azedit Software Manual Download Page 165

Page: 165 / 182

Telex Communications

165

Ok ?

Indicates that the data device connected to the port is a keypanel with an unknown or earlier version of software.

OK TIF

Indicates that the data device connected to the port is a TIF-951 or TIF-2000 Telephone Interface.

Port status bitmap grid

The

Port Status Bitmap Grid

displays the following icons in the Port Status group (upper-right corner of the

Keypanels / Ports screen). Most of these icons activate based on keypanel features detected by the intercom system
master controller.

Heartbeat Icon

: Indicates that a data device (keypanel, TIF, or Camera Delegate Panel) is connected to the intercom

port

Warning Icon

: Indicates that the intercom port is defined as an IFB output (in the IFB Setup screen).

Headset Icon

: Indicates that the connected keypanel has a headset selected

LED Icons

: Indicate the on/off state of any local GPI inputs and outputs. These indicators function only when a

keypanel with a local GPI port is connected. Green=On (Asserted), Red=Off (Inhibited), Gray=None, IN=GPI Input,
OUT=GPI Output.

Question Mark Icon

: Indicates that the keypanel type you have selected (with the Edit button) does not match what

is reported by the intercom system.

Print

Summary of Contents for Azedit























































































































































































Search results

Summary of Contents for Azedit

Reviews:

Related manuals for Azedit

Brands by name

Popular brands

Telex Azedit, Software Manual

Search results

Summary of Contents for Azedit

Reviews:

Related manuals for Azedit

Brands by name

Popular brands