Telex Azedit Software Manual Download Page 159 | Manualshive

Page: 159 / 182

background image

Telex Communications

159

N

New

If you are currently editing a file in FILE mode, clicking New will clear all settings and open a new, blank setup file
(you will be prompted for confirmation first).

•

If you are in FILE mode, but no changes have been made, clicking

New

will immediately start a new setup file

without any prompts.

•

If you are in ONLINE mode, clicking

New

will cause the computer to disconnect from the intercom system and

enter FILE mode (you will be prompted for confirmation). A blank setup file is started.

•

If you are operating in SERVER mode, you cannot start a new file.

NOT PL Listener button

Use the

NOT PL Listener

button to make the selected port(s) not permanent listeners (P-L) for the currently viewed

PL assignment.

NOT PL Talker button

Use the

NOT PL Talker

button to make the selected port(s) not permanent talkers (P-T) for the currently viewed PL

assignment.

«
...
157
158
159
160
161
...
»

Summary of Contents for Azedit























































































































































































Reviews:

No comments

Related manuals for Azedit

Brand: Sigma Pages: 55

Brand: Avaya Pages: 20

Brand: AMX Pages: 54

PRIVILEGED USER MANAGER 2.2

Brand: Novell Pages: 37

Brand: Sawgrass Pages: 48

CERTIFICATE SYSTEM 7.3 - ADMINISTRATION

Brand: Red Hat Pages: 554

ALTIRIS SECURITY EXPRESSIONS

Brand: Symantec Pages: 4

ALTIRIS IT MANAGEMENT SUITE 7.0 MR1 - S V1.0

Brand: Symantec Pages: 13

Brand: IBM Pages: 388

PrintNET 7.X Enterprise

Brand: KIP Pages: 37

Brand: Canon Pages: 50

AltiWare ACC 5.1

Brand: Altigen Pages: 383

AltiWare ACC 5.2

Brand: Altigen Pages: 399

ThinkStation D20

Brand: Lenovo Pages: 272

Australia Asset Library

Brand: Panasonic Pages: 9

Brand: Panasonic Pages: 48

Brand: Oki Pages: 39

Brand: Cisco Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands