Telex Azedit Software Manual Download Page 151

Page: 151 / 182

Telex Communications

151

Gain

Use

Gain

to adjust crosspoint and party line gains. Increase the level of a sound by increasing the amplitude of the

frequency. A volume control essentially adjusts gain for an audio/video system. Gain is simply the increase of a
signal. Typically, higher gain is better.

Go Back

reverts to previously viewed windows, up to 20 consecutively previous screens.

Go Back is available in the View menu and also via the Go Back button.

Go Forward

allows you to follow the same sequence of windows you used with Go Back. Go Forward is used in

conjunction with Go Back.

ORWARD IS AVAILABLE IN THE

IEW MENU AND ALSO VIA THE

ORWARD BUTTON

Summary of Contents for Azedit























































































































































































Search results

Summary of Contents for Azedit

Reviews:

Related manuals for Azedit

Brands by name

Popular brands

Telex Azedit, Software Manual

Search results

Summary of Contents for Azedit

Reviews:

Related manuals for Azedit

Brands by name

Popular brands