Telex Azedit Software Manual Download Page 173 | Manualshive

Page: 173 / 182

background image

Telex Communications

173

Standby Controller Status

Use

Standby Controller Status

to view connection status and data communication errors between the standby

master controller card and the active master controller card.

Standby Controller Status Screen Information

Stby MC Status - Status Column

"-- --"

The

Stby MC Status - Status

columns show the status between the master controller and the standby master

controller Two consecutive dashes indicate that there has never been any data communication between the standby
controller and the master controller during the current edit session. This could be because the device is not
connected.

Bad Cut

:

Indicates that there was a connection to the standby controller, but it is now not connected or there may be a power
failure or other problem somewhere in the system.

OK Cur:

Indicates that the standby controller is connected and operating, and that it has been updated with the current
intercom system configuration.

OK Old:

Indicates that the standby controller is connected and operating, but that it has not been updated with the current
intercom system configuration.

Status Bar

Status Bar

activates the status bar at the bottom of the AZedit window.

Toolbar is available under the View menu.

«
...
171
172
173
174
175
...
»

Summary of Contents for Azedit























































































































































































Reviews:

No comments

Related manuals for Azedit

SCX 4500 - B/W Laser - All-in-One

Brand: Samsung Pages: 21

SCX 4828FN - Laser Multi-Function Printer

Brand: Samsung Pages: 38

SCX 4725FN - B/W Laser - All-in-One

Brand: Samsung Pages: 33

Remote Client Software V 4.0.1

Brand: Q-See Pages: 72

SADPmini Logger

Brand: Alpha Moisture Systems Pages: 14

08011-41-UD2-003

Brand: Canon Pages: 176

Brand: Honeywell Pages: 2

Brand: Honeywell Pages: 14

7850LP-I1-5210E - Hand Held Products Dolphin 7850

Brand: Honeywell Pages: 36

Brand: Honeywell Pages: 46

RAPID EYE MULTI-MEDIA

Brand: Honeywell Pages: 144

Brand: Honeywell Pages: 160

Brand: Honeywell Pages: 176

Dolphin Power Tools

Brand: Honeywell Pages: 176

Brand: Juniper Pages: 24

JUNOS OS 10.3 - SOFTWARE

Brand: Juniper Pages: 3946

AutoCAD Civil 3D 2013

Brand: Autodesk Pages: 25

Brand: Autodesk Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands