Telex Azedit Software Manual Download Page 24 | Manualshive

Page: 24 / 182

background image

Telex Communications

24

General Keypanel Setup

To setup a keypanel do the following:

1. On the Keypanel / Ports screen, select the intercom port you want to setup.

Use either of the following methods:

In the Port text box, enter the intercom port number, and then press Enter.
OR
From the Alpha drop down list, select the port alpha.

Note: If all key assignments are disabled (grayed out) on the selected intercom port and "Trunk
Port" displays at the top of the screen, this means the port is reserved for trunking and cannot be
used for any other purpose. To reclaim the port, you must run CSTrunk and remove the trunking
allocation.

2. Click Edit.

The Keypanel / Port Configuration Setup screen appears.

3. Verify or make the necessary changes to the Setup screen.

4. Click the Advanced tab.

The Advanced screen appears.

5. Verify or make the necessary changes to the Advanced screen.

Note: While editing the Setup or Advanced settings you can click Apply at any time to enter your
changes without closing the screen.

6. Click OK to save the changes made. Otherwise click Cancel.

The Keypanel / Port Configuration screen closes.

«
...
22
23
24
25
26
...
»

Summary of Contents for Azedit























































































































































































Reviews:

No comments

Related manuals for Azedit

Brand: ZixCorp Pages: 44

Brand: Brother Pages: 22

Brand: Brother Pages: 115

Brand: Acroprint Pages: 1

TRUE IMAGE CORPORATE WORKSTATION 8.0

Brand: ACRONIS Pages: 79

TRUEIMAGE DELUXE

Brand: ACRONIS Pages: 90

Brand: ACRONIS Pages: 97

NetAtlas Workgroup

Brand: ZyXEL Communications Pages: 242

Brand: Konica Minolta Pages: 6

CODESOFT Sentinel Print Pack

Brand: Techniques Avancees Pages: 50

Brand: GRASS VALLEY Pages: 2

Brand: GRASS VALLEY Pages: 24

AURORA INGEST - S AND UPGRADE INSTRUCTIONS V7.1

Brand: GRASS VALLEY Pages: 66

495B1-05A111-1301 - 3ds Max Design 2010

Brand: Autodesk Pages: 916

Brand: GAI-Tronics Pages: 5

PERFORMANCE MANAGEMENT FOR POWER SYSTEMS - INTERACTIVE GRAPHING SUPPORT FOR ...

Brand: IBM Pages: 29

ANTI-VIRUS 5.0 - FOR SENDMAIL WITH MILTER...

Brand: KAPERSKY Pages: 100

TIVOLI SC23-8765-00

Brand: IBM Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands