manualshive.com logo in svg

TECO-Westinghouse A510, Instruction Manual

Share
Download
TECO-Westinghouse A510 Instruction Manual Download Page 345

 

 

 

 

 

 

4-270 

Slip compensation

Frequency

Reference

18-01

18-00

 

 

Figure 4.4.102 18-00/18-01

 

Slip compensation gain versus frequency reference 

 

Torque

Speed

Decrease 

18-01

Decrease 

18-01

Increase

 18-01

Increase

 18-01

 

Figure 4.4.103 18-01 Effect on torque speed curve   

 

18-05:

 FOC (Flux Orient Control) delay time 

 

In the SLV mode, the slip compensation of the magnetic flux depends on the torque current and excitation current. 

If the motor load rises above 100% while running at the motor rated frequency, the motor voltage and resistance 

drops sharply, which may cause the inverter output to saturate and current jitter occur. The magnetic flux slip 

compensation will independently control the torque current and the excitation current to prevent current jitter. For 

slow speed or fixed speed operation, 18-05 may be increased. For fast operation adjust 18-06. 

 

18-06:

 Slip compensation gain 

 

If the motor is jittering at the rated frequency under full load, the value of 18-06 may gradually be reduced to zero 

to reduce current jitter. 
 

SLV2 mode adjustment 

 
Default value of parameter 18-00 is 0.0. ( when 18-00 = 0.0, slip compensation function is off.)

 

Adjustment of slip compensation gain (18-00) is the following:   

a) 

Correctly set the rated slip and no-load current (02-00).   

b) 

Set slip compensation gain (18-00). 

c) 

Run under load. Measure the speed and adjust slip compensation gain (18-00) with the unit of 0.1.   

 

Notes: 

─  If  the  motor  speed  is  lower  than  the  target  speed,  increase  the  setting  value  of  low-speed  slip 

compensation gain (18-00).   

─    If  the  motor  speed  is  higher  than  the  target  speed,  reduce  the  setting  value  of  low-speed  slip 

compensation gain (18-00).   

Summary of Contents for A510












































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands