manualshive.com logo in svg

ST ST10F276E, User Manual, Page: 322 / 564

Share
Download
ST ST10F276E User Manual Download Page 322

The bootstrap loader

UM0404

322/564

DocID13284 Rev 2

15.6.7 

Alternate boot user software

If the rules described here before are met (that is,: mapping of variables, disabling of 
interrupts, exit conditions, predefined vectors in Block 0 of Bank 2, Watchdog usage) then 
users can write the software they want to execute in this mode starting from 09’0000h.

15.6.8 

User/alternate mode signature integrity check

The behavior of the Alternate Boot Mode is based on the computing of a signature between 
the content of two memory locations and a comparison with a reference signature. This 
requires that users who use Alternate Boot have reserved and programmed the Flash 
memory locations according to: 

User mode signature

00'0000h: memory address of 

operand0

 for the signature computing

00’1FFCh: memory address of 

operand1

 for the signature computing

00’1FFEh: memory address for the signature reference

Alternate mode signature

09'0000h: memory address of 

operand0

 for the signature computing

09’1FFCh: memory address of 

operand1

 for the signature computing

09’1FFEh: memory address for the signature reference

The value for 

operand0, operand1

 and the signature should be such that the following 

sequence should be successfully executed:

MOV

Rx, CheckBlock1Addr; 00’0000h for standard reset

ADD

Rx, CheckBlock2Addr; 00’1FFCh for standard reset

CPLB

RLx

; 1s complement of the lower
; byte of the sum

CMP 

Rx, CheckBlock3Addr; 00’1FFEh for standard reset

15.6.9 Alternate 

boot 

user software aspects

User defined alternate boot code must start at 09’0000h. A new SFR has been created on 
ST10F276 to indicate that the device is running in Alternate Boot Mode: bit 5 of EMUCON 
(mapped at 0xFE0Ah) is set when the alternate boot is selected by the reset configuration. 
All the other bits should be ignored when checking the content of this register to read the 
value of bit5.

This bit is a read only bit. It remains set until next software or hardware reset.

15.6.10 EMUCON 

register

EMUCON (FE0Ah / 05h)

SFR

Reset Value: - - xxh

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

-

ABM

-

R

-

Summary of Contents for ST10F276E





















































































































































































































































































































































































































































































































































































Reviews:

No comments