manualshive.com logo in svg

Splicecom 4100, Installation & Maintenance Manual

The Kestrel 4100 Quick Start Manual is now available for free download on manualshive.com. This comprehensive user manual provides step-by-step instructions to set up and operate your Kestrel 4100 device effortlessly. Get the most out of your purchase and enhance your experience with this user-friendly manual.

Share
Download
background image

Installation and Maintenance Manual

 

 

 

 

 

Field Descriptions 

336 

 

Installation and Maintenance Manual v4/0615/10 

 

Prepend 

Format of international numbers presented by the SIP provider, eg 00 

 

Outgoing Prepend 

Format of international numbers required by the SIP provider for outgoing calls, eg 00 

 

Call Server 

Determines the Call Server to be used for this trunk. 

 

H323 Page 

Compression Type 

None 

Calls to be made without using compression 

G729A8K 

Use G.729a based compression supported via a Voice Compression Module or Card 

Relay 

Relay the media packets, allowing RTP packets to go through a NAT/firewall by using the 

Call Server as a single address for all RTP 

 

Allow Non-Compressed Audio 

Enable/Disable.  For use with G.729 Compression Type.  This option will allow A-law or u-law to be 

selected by the remote endpoint instead of G.729. 

 

NAT Server 

IP address allocated by the ADSL provider, in xxx.xxx.xxx.xxx form 

 

NAT Port 

Port to be used by NAT = 1720 

 

NAT Mode 

Static 

Use IP address entered above 

STUN 

For future use 

 

Allow Fast Start 

Enable/Disable.  Must selected at both ends. Required for link from Call Server to Call Server. 

 

Allow Hold Music 

Enable/Disable.  For use when this trunk is connected to another Call Server.  If enabled, this option will 

send hold music information on this trunk. 

 

Calls Server 

Determines the Call Server to be used for this trunk. 

Trunk Groups 

Name 

64 Domain Characters.  Name of the Trunk Group. 

 

Description 

128 Characters.  A text field to enter the description of this Trunk Group. 

 

Summary of Contents for 4100























































































































































































































































































































































































Reviews:

No comments

Related manuals for 4100

PaloAlto Networks M-100 Hardware Reference Manual preview
M-100
Brand: PaloAlto Networks Pages: 30
G-Technology G-DRIVE ev ATC Product Manual preview
G-DRIVE ev ATC
Brand: G-Technology Pages: 35
IBM eServer 130 xSeries User Reference Manual preview
eServer 130 xSeries
Brand: IBM Pages: 156
IntesisBox Modbus Server-FC330A Installation Manual preview
Modbus Server-FC330A
Brand: IntesisBox Pages: 5
IBM 847620U - Netfinity 3000 - 20U Hardware Maintenance Manual preview
847620U - Netfinity 3000 - 20U
Brand: IBM Pages: 270
Omneon MediaGrid ContentServer 3000 Quick Reference Manual preview
MediaGrid ContentServer 3000
Brand: Omneon Pages: 2
IBM 8676 - Eserver xSeries 335 Hardware Maintenance Manual And Troubleshooting Manual preview
8676 - Eserver xSeries 335
Brand: IBM Pages: 172
Supermicro SuperServer E300-9C User Manual preview
SuperServer E300-9C
Brand: Supermicro Pages: 113
Simpact Freeway 1200 Hardware Installation Manual preview
Freeway 1200
Brand: Simpact Pages: 76
Atop ABLELink GW21W User Manual preview
ABLELink GW21W
Brand: Atop Pages: 52
Stratus ftServer 2500 Site Planning Manual preview
ftServer 2500
Brand: Stratus Pages: 106
Hitachi F1500 Hardware Manual preview
F1500
Brand: Hitachi Pages: 208
Hitachi AMS 2500 Getting Started Manual preview
AMS 2500
Brand: Hitachi Pages: 36
Wegener iPump 562 User Manual preview
iPump 562
Brand: Wegener Pages: 33
IBM eserver xSeries 350 User Reference Manual preview
eserver xSeries 350
Brand: IBM Pages: 174
Axis AXIS 570 User Manual preview
AXIS 570
Brand: Axis Pages: 316
Meinberg LANTIME M100 Constructions And Installations Instructions preview
LANTIME M100
Brand: Meinberg Pages: 4
Meinberg LANTIME M600 MRS User Manual preview
LANTIME M600 MRS
Brand: Meinberg Pages: 160

Brands by name

Popular brands

Load more brands