Splicecom 4100 Installation & Maintenance Manual Download Page 311

Page: 311 / 374

Installation and Maintenance Manual

Field Descriptions

Installation and Maintenance Manual v4/0615/10

307

NoBeep

Enables Call Waiting but the intermittent beep is disabled. The User will be informed of

a call waiting on the screen of their PCS 58x/57x/56x/55x, PCS 410/400, PCS 100, PCS 60

or PCS 50.

Outgoing Call Bar

Enable/Disable. When enabled the User cannot make external calls.

Require Account Coding

Enable/Disable. When enabled the User must enter an Account Code before making an external call.

No Answer Time

The amount of time (in seconds) the User’s extension will ring before it is considered not answered.

(Default = 20 seconds)

Dial Plan

Name (GUID) of the Dial Plan used by the User.

Park Slot Base

Number. For use with the PCS. The value to be added to the existing Park Slot numbers accessed via the

Park icons.

Park Slot Offset

Number. For use with the PCS. Specifies from which existing Park Slot number the Park Slot Base value

will be added.

8 Digits. The access code required to

be entered to “login” as this U

ser.

This must match the User’s

Voicemail Access Code if the User is a Vision Agent and will be using the Vision Agent Portal to log on to

their handset. Please refer to the Vision Call Centre Configuration manual for further details.

If a User has been manually logged in, then this is the amount of time (in seconds) the user can be idle

before they are automatically logged out. 0 = never log out. Default = 18000 seconds.

Remote Working Code

Authorisation code to enable Extension Anywhere for the User. Also required if this User is a Vision Call

Centre Agent, and/or will be utilizing the Vision Supervisor Console software, and/or utilizing the Vision

Mobility application. In all cases this must be the same as the Partner Login Code for the phone that this

User is assigned to. If the Vision Agent is using the Vision Agent Portal to log on to a handset this must

also match the handset’s Partner Login Code.

Supervisor of

For future use.

DND page

Out Of Office

Message to be displayed on a PCS 50, 60, 100, 410/400, 55x, 58x/57x/56x when a call is made to this User.

In Office (disabled), In Meeting, Lunch (displayed as On Lunch), On Holiday, Off Site. The option

selected will activate the relevant voicemail greeting, eg the In Meeting voicemail greeting, At Lunch

voicemail greeting and so on.

Summary of Contents for 4100























































































































































































































































































































































































Search results

Summary of Contents for 4100

Reviews:

Brands by name

Popular brands

Splicecom 4100, Installation & Maintenance Manual

Search results

Summary of Contents for 4100

Reviews:

Brands by name

Popular brands