Splicecom 4100 Installation & Maintenance Manual Download Page 180

Page: 180 / 374

Installation and Maintenance Manual

Configuring system functionality

176

Installation and Maintenance Manual v4/0615/10

In both cases the User would be asked for the conference PIN if configured and a beep would confirm

that the conference has been successfully started.

A Meet Me Conference can be started via a DDI Plan

entry similar to this example. Please note that Translate

to field can contain !CC or !ConferenceCreate.

After dialling the DDI number the user will be asked to

enter the conference number followed by #, eg 7987#.

If a number has been entered in the Pin field for this

conference the user will be asked to enter the

conference PIN followed by #, eg 1234#. A beep will

confirm that the conference has been successfully

started.

Users and external contacts can then join a conference either via a Dial Plan entry or DDI Plan entry as

described below in Joining a Meet Me Conference. (However, please note that if a User dials a Dial Plan

entry or DDI Entry similar to those described above for a conference that had already been started this

User would join the conference.)

Both the Dial Plan entry and DDI Plan entry described above can be used to create and start a new Meet

Me Conference. When asked for the conference number any number can be entered unless used for an

existing Meet Me Conference. A Meet Me Conference entry will be automatically created and can be

viewed via Manager. The extension number or DDI number of the originator of the conference will be

displayed in the Organiser field. The Start Time field will contain the time the conference was initiated

and the End Time field will contain the time 30 minutes later. This means Users must join this

conference, as described below, within 30 minutes of its creation. The conference will be open for as

long as someone is in the conference, however if a User drops out they will not be able to join again if

the 30 minutes has passed. If the User initiating the conference belongs to a Company the Meet Me

Conference entry will be displayed under the specific Company within Manager. Please refer to the

Working with Companies section from page 177 for further information.

A Dial Plan entry can also be used to create and start a Meet Me Conference where the conference

number is the extension number of the User that originated the conference. In this case the Translate To

field would contain !ConferenceCreate:%s or !CC:%s.

Joining a Meet Me Conference

A Meet Me Conference can be joined via a Dial Plan entry or DDI Plan entry.

To allow Users to join a Meet Me Conference internally

a Dial Plan similar to this example can be used. Please

note that Translate to field can contain !CJ or

!ConferenceJoin.

Summary of Contents for 4100























































































































































































































































































































































































Search results

Summary of Contents for 4100

Reviews:

Related manuals for 4100

Brands by name

Popular brands

Splicecom 4100, Installation & Maintenance Manual

Search results

Summary of Contents for 4100

Reviews:

Related manuals for 4100

Brands by name

Popular brands