Splicecom 4100 Installation & Maintenance Manual Download Page 154

Page: 154 / 374

Installation and Maintenance Manual

Configuring system functionality

150

Installation and Maintenance Manual v4/0615/10

If Rotary or Sequential Mode is

selected the No Answer Time will

determine how long the call will ring

on each extension before moving to

the next extension. Select the

Telephony page and in the No

Answer Time field enter the number

of seconds required.

Select Update or Apply when ready.

Please note:

Comfort announcements can be played to the caller while waiting for the call to be answered.

Please refer to page 241 for further information.

If the Max Number of Active Calls before Busy entry has been exceeded the caller will be given busy

or presented to voicemail.

Calls will pass to voicemail after the time entered in the Max No Answer Time before Voicemail field.

Please refer to page 233 for further details.

These settings can also be viewed within Manager Assist>Configuration Aids> Departments

–

Display

and Highlight Issues.

Using an Alternate Distribution Group

If members of the Distribution Group are unavailable to take a call it can be passed to an Alternate

Distribution Group. The Max Ring Time Before Alternate Distribution field determines how long the call

will ring round the Distribution Group without being answered before being passed to the Alternate

Distribution Group. The Alternate Distribution Mode will determine how the calls will be presented to the

Alternate Distribution Group.

In Manager select Departments

A list of the current Departments are displayed

Select the Department required

Select the Distribution page

Select the Distribution Skip On No Targets check box if a call is to be presented immediately to the

Alternate Distribution Group when all members of the Distribution Group are busy. Only used with

the Rotary and Sequential Distribution modes.

Select the Alternate Distribution Group

field.

From the Select Group list select the

Group required and this Group will be

displayed in the Alternate Distribution

Group field

From the Alternate Distribution Mode list box select the method to be used to distribute the calls:

All

–

all members of the Group are presented with the call simultaneously. This mode will

allow you to reject a call (using a PCS) without it coming back a few seconds later.

Rotary

–

a call will be presented to the member of the Group with the highest Order number.

If that member is unavailable it will be presented to the User with the next highest number

and so on. The system will always attempt to present a new call to the member with the

highest Order number.

Sequential

–

same as Rotary however subsequent calls will be presented to the next User in

the Group after the User who was last presented with a call.

Summary of Contents for 4100























































































































































































































































































































































































Search results

Summary of Contents for 4100

Reviews:

Brands by name

Popular brands

Splicecom 4100, Installation & Maintenance Manual

Search results

Summary of Contents for 4100

Reviews:

Brands by name

Popular brands