Splicecom 4100 Installation & Maintenance Manual Download Page 299

Page: 299 / 374

Installation and Maintenance Manual

Maintenance & Troubleshooting

Installation and Maintenance Manual v4/0615/10

295

The version of software being used by the PCS 100 can be viewed by pressing the down arrow on the

handset; the current software version will be displayed at the bottom of the screen. Press the down

arrow or up arrow to return to the previous screen.

Upgrading locally

On the PCS 100 lift the handset.

Press the Speaker button while rebooting the unit.

The boot menu will be displayed

Press hash (#)

The unit will be upgraded and the reboot will complete

Upgrading remotely via Telnet
You will need to know the IP address of the PCS 100 which can be viewed via the following three

methods:

During power up of the phone.

After power up press the down arrow on the handset, the IP address and current software version

being used by the PCS 100 will be displayed on the screen. Press the down arrow or up arrow to

return to the previous screen.

A list of the IP address for each PCS 100 can be viewed in Manager Assist by selecting System

Utilities and then IP Addresses.

You will also need to know the

phone’s Password

which is configured in Manager within the relevant IP

Phones’ configuration form. By default this is set to 7388.

Within the Command Prompt on a PC connected to the system enter:

telnet <ip address of PCS 100>

eg telnet 192.168.0.247

When prompted for the Login name enter

diag

When prompted for the Password enter the password for this phone. By default this is

7388

(The

Password is set within the relevant Phone’s configuration form.)

A hash (#) will appear, indicating that the previous entries where accepted and a command can be

entered

Enter

upgrade loader <IP address of Call Server>

eg upgrade loader 192.168.0.1

When the hash (#) returns enter

upgrade now

upgrade now <IP address of Call Server supplying the software>

eg upgrade now 192.168.0.1

The PCS 100 will reboot. When the PCS 100 is ready press the down arrow to check the version

number to ensure the upgrade has taken place.

View the version of software via Telnet
The version of software being run on the PCS 100 can be viewed using Telnet as described above by

entering:

ver /Splicecom/xpcs

Automatic Upgrade

The upgrade of any connected Phone Module, Trunk Module, VCM, PCS 58x, PCS 57x, PCS 56x, PCS 55x,

PCS 542, PCS 410/400 and PCS 100 as described above will take place automatically at 4 am each day. At

this time a php script will be run and any module or PCS 58x/57x/56x/55x/542, PCS 410/400 and PCS 100

not running up-to-date software will be upgraded. This will take place on each module or

PCS 58x/57x/56x/55x/542, PCS 410/400 and PCS 100 that the Call Server can connect to at 4 am. If the

Summary of Contents for 4100























































































































































































































































































































































































Search results

Summary of Contents for 4100

Reviews:

Brands by name

Popular brands

Splicecom 4100, Installation & Maintenance Manual

Search results

Summary of Contents for 4100

Reviews:

Brands by name

Popular brands