Splicecom 4100 Installation & Maintenance Manual Download Page 62

Page: 62 / 374

Installation and Maintenance Manual

System Configuration

Installation and Maintenance Manual v4/0615/10

Changing the logo displayed on a PCS 57x and PCS 56x

Rename the graphic file to

logosmall.png

and copy this file into the ftp directory on the Call Server

(for information on how to access the ftp directory please refer to the Admin Access to a Call Server

from page 273 for further details).

Telnet on to the Call Server (as described in the Root Access to a Call Server section from page

272).

Enter

cd /SpliceCom/ftp

Enter

and ensure your logosmall.png file is available here

Enter

cd /SpliceCom

Enter

mkdir pcs5xx

(you can use

here to ensure the directory has been created)

Enter

cd pcs5xx

Enter

mkdir logos

(you can use

to ensure the directory has been created)

Enter

mv /SpliceCom/ftp/logosmall.png logos/logosmall.png

(you can change to the logos directory and check that the file has been moved to here.)

Enter

cd /SpliceCom

Enter

/SpliceCom/pcs5xx_customise pcs5xx pcs5x1-256M.site

(for the PCS 572/562 phones)

/SpliceCom/pcs5xx_customise pcs5xx pcs5xx-256M.site

(for the PCS 570/560 phones)

You will receive a message indicating that the customisation file is ready for the upgrade.

The logo displayed within the Home screen will now change when an upgrade is performed on

the handset. (For details on how to perform an upgrade (even if the software version stays the

same) please refer to the Upgrading the Software on the PCS 57x, PCS 56x, PCS 55x and PCS 542

section from page 292.)

Please note

To remove a custom logo, delete the site file and default the configuration of the phone (for further

details please refer to the Initial Configuration Boot Menu section from page 297), however this will

also default any configuration within Setnet.

Alternatively, rename the logo file, run pcs5xx_customise to create the site file and then upgrade the

phone as normal.

The logo displayed on the Home screen can be specified on a per User basis via their Logo URL

field. This will take precedence over the site file. Please refer to the Configuring a User section from

page 95 for further details.

Summary of Contents for 4100























































































































































































































































































































































































Search results

Summary of Contents for 4100

Reviews:

Related manuals for 4100

Brands by name

Popular brands

Splicecom 4100, Installation & Maintenance Manual

Search results

Summary of Contents for 4100

Reviews:

Related manuals for 4100

Brands by name

Popular brands