Splicecom 4100 Installation & Maintenance Manual Download Page 242

Page: 242 / 374

Installation and Maintenance Manual

Working with Voicemail

238

Installation and Maintenance Manual v4/0615/10

Select Update or Apply when ready.

Please note: Ensure that the relevant Voicemail Port has been configured with a Dial Plan otherwise the

voicemail server will not be able to dial the digits entered in the Voicemail Assistant Telephone Number

field.

Accessing voicemail

A User can access a Department’s messages via a Dial Plan entry, via Voicema

il Call Back or via their

PCS 58x/57x/56x/55x/542, 410/400, 100, 60 and 50 (please refer to the Setting Department Voicemail

Notification section from page 239 for further details).

The Department’s

Message Box Mode will determines how voicemail messages for this Department are

listened to when two or more Users simultaneously accesses this Department’s voicemail.

Normal

Users will be able to listen and handle all messages at the same time

Queued Users will not listen to the same message simultaneously. First User to access this

Department’s voicemail will listen to message 1, then the next User will listen to message 2

and so on.

Accessing Department voicemail via a Dial Plan entry

If a Dial Plan entry is to be used to access voicemail

for a Department this diagram gives an example entry

that could be created.

The Translate To field must contain the Department’s

extension number.

Please refer to the Working with Dial Plans section from page 130 for further information on creating Dial

Plan entries.

Summary of Contents for 4100























































































































































































































































































































































































Search results

Summary of Contents for 4100

Reviews:

Brands by name

Popular brands

Splicecom 4100, Installation & Maintenance Manual

Search results

Summary of Contents for 4100

Reviews:

Brands by name

Popular brands