Splicecom 4100 Installation & Maintenance Manual Download Page 108

Page: 108 / 374

Installation and Maintenance Manual

Configuring system functionality

104

Installation and Maintenance Manual v4/0615/10

Dual Personal External -

all external calls to the User’s extension number and DDI will be

forwarded, and the User’s extension will ring. (Calls to the User’s Department(s) will ring on

the User’s extension.)

All External -

all external calls to the User’s extension number and DDI will be forwarded plus

any calls to a Department to which the User is a member.

Dual All External -

all external calls to the User’s extension number and DDI will be forwarded

plus any calls

to a Department to which the User is a member, and the User’s extension will

ring.

Personal Internal -

all internal calls to the User’s extension number and DDI will be forwarded

Dual Personal Internal -

all internal calls to the User’s extension number a

nd DDI will be

forwarded, and the User’s extension will ring. (Calls to the User’s Department(s) will ring on

the User’s extension.)

All Internal -

all internal calls to the User’s extension number and DDI will be forwarded plus

any calls to a Department to which the User is a member.

Dual All Internal -

all internal calls to the User’s extension number and DDI will be forwarded

plus any calls to a Department to which the User is a member, and the User’s extension will

ring.

In the Follow Me To field enter the number to which calls should be routed. This can be an

internal extension or an external number eg a mobile number.

Select Update or Apply when ready.

Calls to this extension will now follow the User to the number configured and the following will take

effect: -

If the Follow Me To number also has Follow Me set the call will be forwarded on.

If the Follow Me To

number is not answered within the original User’s No Answer Time the call will

be routed to the original User’s

voicemail, no further forwarding occurs.

If the Follow Me To number is not answered within

the original User’s No Answer Time and the

original user has Forward on No Answer set the call will be forwarded to this number.

If the Follow Me To number is busy the call will be routed t

o the original User’s

voicemail, no further

forwarding occurs.

If the Follow Me To number is busy and the original User has Forward on Busy set this will be

ignored, the call will be routed to the original User’s

voicemail, no further forwarding occurs.

If the Follow Me To number is a Department extension number and a call is not answered and is

routed to voicemail this will be the Department’s voicemail not the original User’s voicemail

If an external Follow Me To number has a voicemail service, eg a mobile, and this voicemail service

answers the call no further forwarding will occur.

A broken dial tone

on the User’s handset may indicate that

Follow Me has been set.

Dual Personal and Dual All options are useful for staff that regularly move away from their desks, for

example, IT support staff. A call can be answered either at their desk or on, for example, their

mobile, whichever is the easiest at the time.

Summary of Contents for 4100























































































































































































































































































































































































Search results

Summary of Contents for 4100

Reviews:

Related manuals for 4100

Brands by name

Popular brands

Splicecom 4100, Installation & Maintenance Manual

Search results

Summary of Contents for 4100

Reviews:

Related manuals for 4100

Brands by name

Popular brands