Splicecom 4100 Installation & Maintenance Manual Download Page 186

Page: 186 / 374

Installation and Maintenance Manual

Configuring system functionality

182

Installation and Maintenance Manual v4/0615/10

Working with Trunks

The Trunks section of the configuration enables the configuration of ISDN, SIP, H.323 and DPNSS

connections to the system.

The following number of concurrent connections (trunks) are supported:

S8004-S8050

–

S8100

–

120

S716

–

5100

–

5108

–

5500 NSG

–

5200 Trunk

–

I208

–

I230

–

One system can support up to 5,000 simultaneous connections.

The following number of connections are supplied by default with a system:

S8004 Starter Pack

–

4 channels

S716 Starter pack

–

2 channels

5100 Call Server

–

BRI1- 2 channels, BRI2

–

2 channels, PRI1

–

1 channel.

5108 Call Server

–

BRI1

–

2 channels

5500 NSG

–

BRI1

–

2 channels, BRI2

–

2 channels

I208

–

BRI1

–

2 channels

I230

–

PRI1

–

8 channels

This default configuration can be viewed as follows:

In Manager select Trunks

Select the module containing the Trunk you wish to view, eg CallServer

Select the ISDN trunk you wish to view

The Capacity field indicates the number of channels available on this Trunk.

The 4100 Call Server and 4200 Trunk module are provided with four BRI ports providing 8 ISDN channels

and a PRI port however to activate a PRI channel a Trunk licence is required. The 4140 Remote Call

Server is provided with four BRI ports making 8 ISDN channels available, 4 channels are active on

Summary of Contents for 4100























































































































































































































































































































































































Search results

Summary of Contents for 4100

Reviews:

Related manuals for 4100

Brands by name

Popular brands

Splicecom 4100, Installation & Maintenance Manual

Search results

Summary of Contents for 4100

Reviews:

Related manuals for 4100

Brands by name

Popular brands