Splicecom 4100 Installation & Maintenance Manual Download Page 43

Page: 43 / 374

Installation and Maintenance Manual

System Configuration

Installation and Maintenance Manual v4/0615/10

If calls are to be made to a Call Server that does not

contain a Voice Compression Card or does not have a

Voice Compression Module connected it is

recommended that the this Intramodule Trunk is also

created.

If fax calls are to be made between two Call Servers

where compression is supported a Dial Plan entry

similar to the this example should be created within

each fax machine’s Dial Plan.

The DialTransparent

Action will allow calls to by-pass an Intramodule Trunk.

A call made via this Dial Plan entry does not consume a

compression channel. (For further information on Dial

Plans please refer to page 130.)

Installing a Voice Compression Card

A Voice Compression Card supports G.729a to compress up to 8 voice calls between two Call Servers. A

card must be fitted at both ends as follows:

4100 Call Server

Remove the lid

Place nylon standoffs supplied in mounting holes located by silk screen logos MTG14 and MTG15.

Fit VCC card to connector J12 and standoffs - take care to correctly align the pins.

Replace the lid.

4140 Remote Call Server

Remove the lid

Place nylon standoffs supplied in mounting holes located by silk screen logos MTG9 and MTG10.

Fit VCC card to connector J11 and standoffs - take care to correctly align the pins.

Replace the lid.

Extension Numbering

Before connecting a Phone Module, P308 or IP Phone to the system as described in the following

sections it is worth considering what extension numbers are required for the Users automatically created

during the set up process.

Once a Phone Module/P308/IP Phone has registered

with the system each analogue port on the Phone

Module and P308 eg Port01, Port02 etc, or IP Phone

port, will be assigned to a User eg Extn2017, Extn2018

etc automatically created during the installation. Each

User will be given an extension number, eg 2017, 2018

etc.

Summary of Contents for 4100























































































































































































































































































































































































Search results

Summary of Contents for 4100

Reviews:

Related manuals for 4100

Brands by name

Popular brands

Splicecom 4100, Installation & Maintenance Manual

Search results

Summary of Contents for 4100

Reviews:

Related manuals for 4100

Brands by name

Popular brands