Siemens SI120 Configuration Manual Download Page 81 | Manualshive

Page: 81 / 100

background image

Input Transmission

81

Siemens Building Technologies

Fire Safety & Security Products

07.2009

15.2 Service 1 & 2

Transmission to Sylcom or as SMS

Service 1 and 2

This parameter defines whether or not the last 10 events of the engineer log is to be transmitted to
service station 1 after triggering of a transmission line. Two different options can be chosen for this
transmission.

z

Immediate transmission after triggering of the transmission line.

z

Transmission only on unset.

"Service transmission" parameter in the "Other Telecom Options" (TM65)in the engineer menu.
This parameter applies to both stations.

Transmission On full set:

All programmed transmission lines are transmitted.

NOTE

Service 2 is used to send SMS to a mobile phone. For this, the according input lines must be en-
abled for transmission.
For this feature the SMN43 is required.

«
...
79
80
81
82
83
...
»

Summary of Contents for SI120





































































































Reviews:

No comments

Related manuals for SI120

Brand: Kasco Pages: 3

EtherNetIP ControlPlex CPC12EN

Brand: E-T-A Pages: 28

Brand: Zeagle Pages: 37

Brand: Harman Pages: 2

Brand: T-Link Pages: 3

Brand: Jabra Pages: 8

Brand: Waterway Pages: 8

Pulsafeeder MPC Vector

Brand: Idex Pages: 114

Brand: Measurement Computing Pages: 32

Brand: IN-COMMAND Pages: 47

Brand: SYCLOPE Pages: 60

FX-COMM4NDER MFX3203

Brand: Magicfx Pages: 16

AQUASNAP 30RA "B"

Brand: Carrier Pages: 36

Brand: TCS Pages: 8

Brand: B meters Pages: 2

Brand: Bartec Pages: 52

Brand: FAAC Pages: 10

Brand: A&D Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands