Siemens SI120 Configuration Manual Download Page 61 | Manualshive

Page: 61 / 100

background image

Keypads

61

Siemens Building Technologies

Fire Safety & Security Products

07.2009

10 Keypads

[TM514] Remote Key-
pads

This menu function enables the following parameters to be programmed for each remote keypad.

z

Partition assignment in idle state (basic partition)

z

Security stage

z

Remote keypad type: normal/intellectual lock

z

Remote keypad buzzer

z

Setting without code

10.1 Default

Partition

Partition Assignment in
Idle State

The LEDs of the remote keypads can only indicate the status of one partition. But because several partitions
can be controlled from one remote keypad, it is necessary to define which partition the LEDs indicate in the
idle state. Immediately a valid user PIN is entered and a partition is selected, the status of this partition is
immediately indicated.

10.2 Keypad

Mode

Keypad Mode

In this menu it’s defined, if the remote keypad is used as a "normal" remote keypad or as a "GV Geistiger
Verschluss” (IL Intellectual Lock) keypad.
Internal = The keypad works

Normal

without linking operation to GV input function.

External = The keypad works in combination with GV(IL). In this case the keypad operation is only acces-

sible with the 2

nd

identification within 20 seconds, when the GV was triggered.

10.3 LEDs

Keypad

LEDs Keypad

LCD
Input status LCD
LED

This parameter must always be set on.
Not relevant
Not relevant

10.4 Buzzer

On

NOTE

In combination with an SAK84/94 the buzzer is activated for 1.5 seconds.

I: Entry Time

The buzzer is activated during the entry time (continuous tone) after triggering a delayed input

O: Exit Time

The buzzer is activated during the setting delay (continuous tone).
When a delayed input is triggered, the continuous tone changes to an intermittent tone (on/off) until all de-
layed inputs are in quiescent state.

A: Alarm

The buzzer is activated on an alarm (continuous tone).

C: Full Set Confirmation

The buzzer is activated for 3 seconds on a positive acknowledgement or outputs for 3 or 6 short buzzes on a
negative acknowledgement

H: Chime,

The buzzer is activated for a short beep and the "Chime" output for one pulse.

NOTE

The chime can be switched on/off by user only for the default partition assigned to a keypad
address. Chime function in other partitions are still activated and can not be switched of. There-
fore it’s recommended to use chime function only in 1 particular partition.

«
...
59
60
61
62
63
...
»

Summary of Contents for SI120





































































































Reviews:

No comments

Related manuals for SI120

Brand: Bartlett Pages: 30

Brand: Haier Pages: 58

Brand: Danfoss Pages: 7

Brand: Fairchild Pages: 2

Brand: Fairford Pages: 233

Brand: YOKOGAWA Pages: 2

ALICAT SCIENTIFIC PC

Brand: Halma Pages: 2

ALICAT SCIENTIFIC PCD

Brand: Halma Pages: 46

Brand: Eaton Pages: 8

Brand: ABB Pages: 44

Brand: Omega Pages: 2

Brand: Zmotion Pages: 34

FAREX SR MINI SYSTEM

Brand: RKC INSTRUMENT Pages: 82

MagicSpeed Series

Brand: Waeco Pages: 76

Brand: Brand Innovations Pages: 56

Pearldex Series

Brand: KaMo Pages: 2

Brand: Vertiv Pages: 2

Brand: Quantum Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands