Siemens SI120 Configuration Manual Download Page 32 | Manualshive

Page: 32 / 100

background image

Inputs

32

Siemens Building Technologies

Fire Safety & Security Products

07.2009

5 =

Triggering only if “Buzzer On” in the keypad parameter is chosen.

7 =

Triggering only after delay.

6.3.30 BA Access Zone

Only part set delayed
(Burglar Alarm Entry
Route)

Brief description: BA external; Internal delay (Reverse function to Input 25)
On part set: Delayed entry and exit triggering in the assigned partition.
On full set: Direct triggering in the assigned partition.

DE, UK

If the input remains triggered to the end of the delay time on setting to part set, the partition is again unset.

All other country ver-
sions

If the input remains triggered to the end of the delay time on setting to part set, the partition remains full set
and an alarm is triggered.

Partition mode:

Unset

Part set

Full set

Effects on the following outputs when the below partition parameters are preset:

1/7

X External

bell

7

2

Internal

bell

1/7

X Strobe

light

X

X

Cannot full set

7

X

Alarm in memory

X

X

Block lock not released

5

5

Buzzer

3/7

X

Burglar alarm system transmission line

3/7

X

Burglar alarm partition transmission line

3/7

X

Transmission line input

Partition parameters:
X =

Triggering regardless of the partition mode.

1 =

Triggering only if the external bell “When Part Set” in the partition parameter is chosen.

2 =

Triggering only if the internal bell “When Full Set” in the partition parameter is chosen.

3 =

Triggering only if "transmission" parameter is chosen.

5 =

Triggering only if “Buzzer On” in the keypad parameter is chosen.

7 =

Triggering only after delay.

6.3.31 BA

Entry

Route

Burglar Alarm Entry Route
(Special Delayed)

Brief description: BA external delay; Internal delay
Delayed entry and exit triggering on Part and Full set in the assigned partition.

DE, UK

If the input remains triggered to the end of the delay time when setting to part set or full set, the partition is
again unset.

All other country versions

If the input remains triggered to the end of the delay time when setting to part set or full set, the partition
remains full set and an alarm is triggered.

Partition mode:

Unset

Part set

Full set

Effects on the following outputs when the below partition parameters are preset:

7

External

bell

7

Strobe

light

7

Alarm in memory

X

X

Block lock not released

5

Buzzer

X

Burglar alarm system transmission line

X

Burglar alarm partition transmission line..

X

Transmission line input

Partition parameters:
X =

Triggering regardless of the partition mode.

5 =

Triggering only if “Buzzer On” in the keypad parameter is chosen.

7 =

Triggering only after delay.

«
...
30
31
32
33
34
...
»

Summary of Contents for SI120





































































































Reviews:

No comments

Related manuals for SI120

Brand: Hamworthy Pages: 10

Brand: GE Pages: 425

Brand: Eaton Pages: 166

Brand: ZEHUS Pages: 28

Brand: Valfonta Pages: 12

Brand: TA Hydronics Pages: 14

Brand: Bang & Olufsen Pages: 80

Brand: Bang & Olufsen Pages: 13

Brand: Harmonic Drive Pages: 25

Brand: Nelson Pages: 8

Brand: Galaxy Control Systems Pages: 5

Brand: Hach Pages: 36

Brand: Hach Pages: 72

Brand: jcm-tech Pages: 8

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13

Brand: Parker Pages: 21

Brand: Parker Pages: 26

Brand: Parallax Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands