Siemens SI120 Configuration Manual Download Page 72 | Manualshive

Page: 72 / 100

background image

ARC

72

Siemens Building Technologies

Fire Safety & Security Products

07.2009

13 ARC

ARC Alarm Receiver Central or CMS Control Management Station is used to follow
up an intervention by a security provider or the police.

[TM61] ARC 1 /
[TM62] ARC 2

This menu function enables the following parameters:

z

Serial protocol

z

Three telephone numbers

z

Transmission protocol

z

Customer number per main partition

z

Code for alarm verification

z

Audio verification

z

Automatic test call

NOTE

The offset for the start of the automatic test call is to be entered in the "Offset test call 1 Tele-
com options" (TM671) in the engineer menu.

13.1 ARC2 Backup ARC1

Backup transmission

This parameter defines whether the event is to be transmitted to Receiver 2 (emergency telephone station 2)
as increased security in the event of an unsuccessful transmission to Receiver 1 (emergency telephone
station 1). This applies only for Receiver 1 to Receiver 2 but not the other way round.

13.2 Serial Port Protocol (ARC1)

Serial Transmission uses SMN42/SMN43 Module only (SI120). Additonnaly
SML2465 can be used (SI220).

During the upgrade from A7 to A8 the parameter serial transmission is switched
off.

SMN42/SMN43 is connected to the control unit but not to the network. Initialization
and local access are set to transmission. If you try to access via the keypad, the
message “transmission on going" will be displayed. Access will be granted after
2’30”.

Callback to a free number: if the control panel does not call the Sylcom station
which initiated the callback but another Sylcom station, the error message which
will be displayed has to be ignored.

«
...
70
71
72
73
74
...
»

Summary of Contents for SI120





































































































Reviews:

No comments

Related manuals for SI120

Brand: Data I/O Pages: 88

Brand: Data Aire Pages: 13

Brand: Salda Pages: 20

Brand: Magnescale Pages: 3

Brand: Zeta Pages: 44

GA Industries 930-DT

Brand: Vag Pages: 4

UNDER CONTROL CP-30A PILOT

Brand: G-Force Pages: 2

RSF-B mini Series

Brand: Harmonic Drive Pages: 32

Brand: Pilz Pages: 32

GA INDUSTRIES Figures 251-D

Brand: Vag Pages: 6

Brand: GBS Elettronica Pages: 32

Brand: PXM Pages: 15

Brand: wattstopper Pages: 4

Brand: Danfoss Pages: 124

Brand: Progres Pages: 2

Brand: ROTORCOMP Pages: 50

Brand: Samson Pages: 96

SecPath NSQ1FAB08D0

Brand: H3C Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands