Siemens SI120 Configuration Manual Download Page 3

Page: 3 / 100

Siemens Building Technologies

Fire Safety & Security Products

07.2009

Contents

Safety .......................................................................................................9

1.1

Target readers...........................................................................................9

1.2

Work safety information ............................................................................9

1.3

Meaning of the written warning notices ..................................................10

1.4

Meaning of the hazard symbols ..............................................................10

Product description ..............................................................................10

2.1

SI120.......................................................................................................10

2.1.1

System Information SI220 vs. SI120.......................................................11

2.1.2

System parameters SI220 vs. SI120 ......................................................11

Miscellaneous........................................................................................12

3.1

On Line Mode..........................................................................................12

3.2

Date/Time Change..................................................................................12

3.3

Keypads messages.................................................................................12

3.4

Auto Test 1/2 in .......................................................................................12

PIN User .................................................................................................13

4.1

User Name ..............................................................................................13

4.2

Type of User............................................................................................13

4.2.1

Create User online ..................................................................................13

4.2.2

Delete User online...................................................................................14

4.2.3

Create User offline ..................................................................................14

4.3

Double PIN

since A8

....................................................................................14

4.3.1

Master PIN of next User..........................................................................15

4.4

Menu Access Rights ...............................................................................15

4.5

Duress PIN..............................................................................................15

4.6

Partition ...................................................................................................15

4.7

Partition Rights........................................................................................16

4.8

Full Set Rights.........................................................................................16

4.8.1

None........................................................................................................16

4.8.2

Partition ...................................................................................................16

4.8.3

Room (x) .................................................................................................16

4.9

Remote Access .......................................................................................16

RF Controls............................................................................................17

5.1

Partition ...................................................................................................17

5.2

Partition Rights........................................................................................17

Inputs .....................................................................................................18

6.1

Hardware Input........................................................................................18

6.2

Input Name..............................................................................................18

6.3

Logical Input Type...................................................................................18

6.3.1

Unused....................................................................................................20

6.3.2

Keyswitch Zone latching Full Set ............................................................20

6.3.3

Keysw. Full set blockschloss ..................................................................20

6.3.4

Keyswitch Zone latching Part Set ...........................................................21

6.3.5

Keyswitch Zone Pulse Full Set ...............................................................21

6.3.6

Keyswitch Zone Pulse Part Set...............................................................21

6.3.7

Final Setting Push Button .......................................................................21

6.3.8

Keypad disabled......................................................................................22

6.3.9

Lock Supervision.....................................................................................22

6.3.10

Geistiger Verschluss (GV) ......................................................................22

6.3.11

Set/Unset Lock........................................................................................22

6.3.12

Alarm Memory Reset (SI220 only)..........................................................22

6.3.13

Universal 1 / Universal 2 .........................................................................22

Summary of Contents for SI120





































































































Search results

Summary of Contents for SI120

Reviews:

Related manuals for SI120

Brands by name

Popular brands

Siemens SI120, Configuration Manual

Search results

Summary of Contents for SI120

Reviews:

Related manuals for SI120

Brands by name

Popular brands