Siemens SI120 Configuration Manual Download Page 16 | Manualshive

Page: 16 / 100

background image

PIN User

16

Siemens Building Technologies

Fire Safety & Security Products

07.2009

4.7 Partition

Rights

Assign the “partition rights” for each partition.

O: Forced Set

{

The user can force the partition to set with inputs (zones) which are not in normal state. If you want to use
this function, you have to define the inputs as bypass able [TM5].
This naturally applies only to inputs which are programmed as bypassable.

U: Unset

The user can switch the partition to unset state.

P: Part Set

The user can switch the partition to part set state.

M: Reset Alarm
(Alarm Memory Re-
set)

X

The user can reset the alarm memory.
Normally, the alarm memory has to be reset in order to set the partition.
Exception: setting with automatic resetting of the alarm memory.

T: Buy Time

The user can extend the time window of the assigned calendar and thus delay the automatic setting. If this
authorization is enabled, the number 9 "Buy time" appears in the user menu authorizations.

B: Bypass Time Slot

The user can block the calendar assigned to the partition from any freely-selectable date/time up to any
freely-selectable date/time.

V: Valid PIN

An Input of the right (valid) PIN activates the Output “Valid PIN” for this Partition

4.8 Full

Set

Rights

4.8.1 None

The user is not able to full set the partition.

4.8.2 Partition

The user is able to full set the partition.

4.8.3 Room

(x)

The user is able to full set only one of the 6 rooms, but not the whole partition.

4.9 Remote

Access

Allow or deny the user for DTMF control. The User PIN Code allows the access au-
thorization.

IMPORTANT

If remote access is enabled for user, the user rights for partition set/unset are
not taken into consideration. If a user has no right to set a partition locally via
keypad, he can do it by DTMF command.

Procudure to use DTMF Commands:

1.

Call the control unit with the (mobile) phone.

Î

A connection to the control unit is made. This lasts approx. 20 seconds.

2.

Wait until a long buzzer sound is heard.

3.

Enter user PIN.

«
...
14
15
16
17
18
...
»

Summary of Contents for SI120





































































































Reviews:

No comments

Related manuals for SI120

Brand: T-Verter Pages: 121

Brand: Happy Pages: 10

Brand: Gardena Pages: 16

Brand: MADRIX Pages: 28

Brand: VAT Pages: 27

Brand: ICP DAS USA Pages: 148

Brand: ICMA Pages: 8

Brand: LAE electronic Pages: 7

Brand: LAE electronic Pages: 2

Brand: Paradox Pages: 2

Brand: Paradox Pages: 44

Brand: Yoshitake Pages: 4

Brand: YOKOGAWA Pages: 20

UTAdvanced UT32A

Brand: YOKOGAWA Pages: 3

Brand: cinetto Pages: 56

Brand: Greenheck Pages: 4

Brand: SILENTRON Pages: 20

Brand: MacroAir Technologies Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands