Siemens SI120 Configuration Manual Download Page 65 | Manualshive

Page: 65 / 100

background image

System

65

Siemens Building Technologies

Fire Safety & Security Products

07.2009

12 System

[TM5] System Parame-
ters

This menu is used for programming the following parameters:

z

System Programming Parameters

z

Up-/Download Parameters

z

Program Versions

12.1 Customer

The Customer name can be defined with the maximum of 16 characters.

12.2 Operator

The Operator name can be defined with the maximum of 16 characters.

12.3 ARC

Name

The Alarm Receiver Station ARC can be defined with the maximum of 16 charac-
ters.

12.4 Telephone

[TM65] Telephone Sin-
tony

The number under which the Control panel control centre is to be reached from Sylcom is to be entered
here, e.g. the number of the terminal without the area or international code. When changing the numbers, all
the digits not used must be overwritten by F.
F = Key

@

12.4.1 Telephone Area Code

If the Telephone number does not provide sufficient digits for dialing purposes, it is
possible to program a dial pre-fix number in the dialer options. The pre-fix will be
dialed before the telephone number when this option is enabled.

12.4.2 Installer

Telephone

Sylcom Telephone
Number

The Installer number is not used for a system function; it is only information for the customer!
As soon as a system failure (Delay time from menu System Input; Mains Failure) will be showed at the key-
pad, there is a possibility to see the installer telephone number by pressing 3 times the question mark button.

«
...
63
64
65
66
67
...
»

Summary of Contents for SI120





































































































Reviews:

No comments

Related manuals for SI120

Brand: S&C Pages: 40

Brand: Warner Electric Pages: 3

Brand: iCeeO2 Pages: 7

Brand: SABAF Pages: 6

Brand: Haier Pages: 58

Brand: Eaton Pages: 2

Brand: Eaton Pages: 2

Brand: Eaton Pages: 8

Brand: Haldex Pages: 8

Brand: Watlow Pages: 4

Brand: Samson Pages: 102

Brand: Allen-Bradley Pages: 16

Brand: D+H Pages: 2

Brand: Anilam Pages: 31

Brand: Rinnai Pages: 7

VARIOMATIC SARV 07.1

Brand: AUMA Pages: 32

iEP-5000G Series

Brand: ASROCK Pages: 2

Brand: Runxin Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands