Siemens SI120 Configuration Manual Download Page 91 | Manualshive

Page: 91 / 100

background image

Engineer Management

91

Siemens Building Technologies

Fire Safety & Security Products

07.2009

Tel.1 Rec.2

Telephone number 1 of Receiver 2

Tel.2 Rec.2

Telephone number 2 of Receiver 2

Tel.3 Rec.2

Telephone number 3 of Receiver 2

Sylcom communication

The central control unit is communicating with Sylcom.

Carrier frequency stop

The carrier frequency was interrupted.

Connected

The central control unit has established a connection with Sylcom.

Identified

The identification with Sylcom is OK.

Transmit / receive

Transmitting or receiving with Sylcom is taking place.

Call

The central control unit detects an incoming call.

Line occupied

The telephone line is occupied.

Up/Down OK

Up/download was successful.

Transmit 2100Hz

The central control unit is transmitting the start frequency.

Transmit carrier frequency

The central control unit is transmitting the carrier frequency.

End connection

The connection to Sylcom is ended.

Callback

The central control unit makes a callback.

Hang up

The central control unit hangs up.

Send data

The central control unit is sending data.

Receive data

The central control unit is receiving data.

Transmission test end

The engineer menu is left during a transmission test. Key

X

must be pressed to end the display of the

transmission state.

19.8.6 Listen

Test

[TM86] Listen test

This menu function enables the audio/video periphery to be tested. An audio module must be fitted in the
central control unit to enable the test to be carried out.

Changeover

After activation of this test, a changeover from one verification zone to the next can be achieved by pressing
the "

Test

" key on the audio module (e.g. WMA 11). The changeover applies for audio and video.

Hearing test

The audio board provides a connection for a headset. This means that each of the verification zones can be
listened to. The microphone sensitivity can then be set as required.

Voice test

By using the voice module (e.g. SMV 11), a voice message can be output over the loudspeaker. In this case,
help text 4 is output each minute via the loudspeaker of the activated verification zone. The volume can be
set as required. If no voice module is used, a tone is output on the loudspeaker each minute for 6 seconds
each time. Steering buttons on the telephone:

z

“Star” button to quit the information and stop the dialling process

z

0” button to hang up the connection

Video test

The video pictures can be displayed on a monitor from the video module (e.g. WMV 11, WAV 61). In this
case the picture of the activated verification zone is always displayed.

«
...
89
90
91
92
93
...
»

Summary of Contents for SI120





































































































Reviews:

No comments

Related manuals for SI120

Brand: YASKAWA Pages: 256

Brand: BADLANDS Pages: 2

Brand: D+H Pages: 36

Brand: D-Box Pages: 4

Brand: D+H Pages: 36

Brand: Kathrein Pages: 16

EP Series Pro-Bloc

Brand: Parker Pages: 11

Brand: Parker Pages: 22

Brand: Parker Pages: 2

Brand: National Instruments Pages: 17

Brand: Davey Pages: 12

Brand: Maximum Controls Pages: 58

Brand: IR-Tec Pages: 14

Brand: Delabie Pages: 20

Brand: Linear Technology Pages: 32

TrueAlarm 4100 Series

Brand: Simplex Pages: 8

Brand: Swagelok Pages: 16

Brand: National Instruments Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands