Siemens SI120 Configuration Manual Download Page 6

Page: 6 / 100

Siemens Building Technologies

Fire Safety & Security Products

07.2009

9.7

Strobe Duration .......................................................................................56

9.8

Emercency Exit .......................................................................................56

9.9

Engineer Reset .......................................................................................56

9.10

Set possible.............................................................................................56

9.11

Setting with Alarm in Memory .................................................................56

9.12

Forced Set...............................................................................................57

9.13

Transmission...........................................................................................57

9.13.1

Burglar Alarm/P. Set ...............................................................................57

9.13.2

Tamper Alarm/P. Set...............................................................................57

9.13.3

Restore Transmission .............................................................................58

9.13.4

Transmission Verification Method...........................................................58

9.14

Input Verified Method ..............................................................................59

9.14.1

Combined Inputs .....................................................................................59

9.14.2

Pulse Counter .........................................................................................59

9.15

Bypass Mode ..........................................................................................59

9.16

Room Management.................................................................................60

9.17

Calendar..................................................................................................60

Keypads .................................................................................................61

10.1

Default Partition.......................................................................................61

10.2

Keypad Mode ..........................................................................................61

10.3

LEDs Keypad ..........................................................................................61

10.4

Buzzer On ...............................................................................................61

10.5

RF Control...............................................................................................62

10.6

Quick Set.................................................................................................62

Video.......................................................................................................63

11.1

Switching Time........................................................................................63

11.2

Video Keypad Address............................................................................63

11.3

Local Video active ...................................................................................63

11.4

Video Mode .............................................................................................63

11.5

Camera Switching Order.........................................................................63

11.6

Timeout ...................................................................................................63

11.7

Alarm with local Video.............................................................................64

11.8

Alarm on Camera ....................................................................................64

11.9

Camera Power Option.............................................................................64

System....................................................................................................65

12.1

Customer.................................................................................................65

12.2

Operator ..................................................................................................65

12.3

ARC Name ..............................................................................................65

12.4

Telephone ...............................................................................................65

12.4.1

Telephone Area Code .............................................................................65

12.4.2

Installer Telephone..................................................................................65

12.4.3

Sintony Telephone ..................................................................................66

12.4.4

MSN Number...........................................................................................66

12.4.5

Number of Attempts ................................................................................66

12.4.6

Number of Rings .....................................................................................66

12.4.7

Dialling Method .......................................................................................66

12.4.8

Line Monitoring........................................................................................66

Summary of Contents for SI120





































































































Search results

Summary of Contents for SI120

Reviews:

Related manuals for SI120

Brands by name

Popular brands

Siemens SI120, Configuration Manual

Search results

Summary of Contents for SI120

Reviews:

Related manuals for SI120

Brands by name

Popular brands