Siemens SI120 Configuration Manual Download Page 67

Page: 67 / 100

System

Siemens Building Technologies

Fire Safety & Security Products

07.2009

12.5 Summer/Winter

Time

Change

[TM72] Change date
and time

This menu function is used to change the date and time. The clock is immediately updated after confirmation.

The hours must be entered using the 24 hour system. The change of date and time is written to the log.

12.6 Sylcom Access when Set

This parameter allows or denies a remote access by a full set system.

12.7 Up/Download

Mode

[TM65] Up/download
if set

This parameter defines whether or not access is permitted via Sylcom (local or remote) on part set or full set.

U = Up/download permitted,

- = Up/download not permitted.

Access options

This parameter defines the access security for an up/download.

No up/download

No up/download possible, Control panel rejects all actions requested by Sylcom.

1 = Level 1

Control panel accepts all actions from Sylcom without local authorization by the user:

Direct call by Sylcom without user authorization,

Callback to a free number without local user authorization,

Callback to programmed number without local user authorization,

2 = Level 2

Control panel accepts all actions with local user authorization. Without user authorization only callback to
pre-programmed number (Service 1).

Callback to a free number with local user authorization,

Callback to programmed number without local user authorization.

3 = Level 3

Control panel accepts only callback to pre-programmed number (Service 1) with local user authorization.

Callback to programmed number with local user authorization.

NOTE

Callback function is not possible over IP!

12.8 Delay

Supervision

[TM5173] Radio monitor-
ing

Delay between 2 supervisons can be set in following way. Defined time depends on the RF gateway type.

SiRoute SiWay

Long 27h

Medium 18h

Short 9h

Very short

4h30

30mn

12.9 RF

Supervision

[TM5173] Radio monitor-
ing

This parameter determines how to handle a RF device fault. If a device is missing you can choose between
tamper alarm, trouble or no supervision

"No" = The central control unit does not detect that a radio alarm no longer exists for whatever reason.

"As a Tamper" = The central control unit triggers a tamper alarm if for whatever reason one no longer

exists.

"As a Trouble" = The central control unit triggers a fault if for whatever reasons one no longer exists

Summary of Contents for SI120





































































































Search results

Summary of Contents for SI120

Reviews:

Related manuals for SI120

Brands by name

Popular brands

Siemens SI120, Configuration Manual

Search results

Summary of Contents for SI120

Reviews:

Related manuals for SI120

Brands by name

Popular brands