Siemens SI120 Configuration Manual Download Page 75

Page: 75 / 100

ARC

Siemens Building Technologies

Fire Safety & Security Products

07.2009

Transmission to Receiver 1 without backup transmission:

Receiver 1

Receiver 2

Tel 1

Tel 2

Tel 3

Transmission to Receivers 1 & 2 without backup transmission:

Receiver 1
Tel 1

Tel 2

Tel 3

Receiver 2
Tel 1

Tel 2

Tel 3

Transmission to Receiver 1 & 2 with backup transmission:

Receiver 1

Receiver 2

Tel 1

Tel 2

Tel 3

X X X X X X X

Transmission to Receiver 2 with or without backup transmission:

Receiver 1

Receiver 2

Tel 1

Tel 2

Tel 3

X X X X X X X

13.7 Test

settings

13.7.1 Automatic

Test

1. Synchronised

The test call synchronizes itself by means of the last transmission.

2. Fixed

The test call is always made at fixed intervals, referring to “Test periodicity”

13.7.2 Automatic

Test

Only when system set

This parameter determines whether the automatic test call is always made or only if the complete system is
set. It enables the automatic test call to be limited to the time period in which the complete system is set.

Summary of Contents for SI120





































































































Search results

Summary of Contents for SI120

Reviews:

Related manuals for SI120

Brands by name

Popular brands

Siemens SI120, Configuration Manual

Search results

Summary of Contents for SI120

Reviews:

Related manuals for SI120

Brands by name

Popular brands