Siemens SI120 Configuration Manual Download Page 54 | Manualshive

Page: 54 / 100

background image

Partitions

54

Siemens Building Technologies

Fire Safety & Security Products

07.2009

Example with Keypad
(SI220 only)

Keypad LCD display show :

PARTITION2
MSMMMMMMMMMMMMMM

--> Partition 2 is Sub-Partition(S), all others are Main Partitions (M)
After Entering Partition 2 the LCD display shows:

S.02 DEP. M01
D * - - D - - - - - - - - - - - - -

--> Sub-Partition 02 is depending on Main Partitions 01 and 05

9.3 Allowed

Keypads

Partition Authorization
for Remote Keypads

Every remote keypad can be assigned to any main partition. This enables the remote keypads to have ac-
cess to individually specified partitions only.
Keypad X  =  Keypad No X has access to this partition
-

= Keypad No X has no access

9.3.1

All Keypads in Part Set

Status Display of Re-
mote Keypads

Active = All indicators and keys active.

9.3.2

All Keypads when Unset

Status Display of Re-
mote Keypads

Inactive = All indicators and keys inactive, only the date and time are shown. Note that in this case
no control can be exercised from the remote keypad, i.e. an input has to be programmed for un
setting and otherwise the partition can no longer be unset.

9.3.3

All Keypads in Full Set

Status Display of Re-
mote Keypads

PIN + LCD = Only the keys for the PIN input and LCD are enabled. The LED displays are blocked.
The buzzer is activated on the delay time. This is then chosen if the continued presence of an alarm is
not to be indicated. -> (No alarm is displayed)

9.4 External

Bell

9.4.1

When Part Set

External Bell on Part Set

All other country ver-
sions

This parameter defines whether the external bell is enabled or not in the event of a burglar alarm on part set.
This parameter also acts on the strobe light output.
Yes = Enabled
No = Disabled

(IT)

This country version is the same as above, but in addion a Panic in unset also activates the external bell if
enabled for part set.

9.4.2 Duration

External Bell Duration

This parameter defines the maximum triggering time of the external bell outputs in the event of an alarm.
Any time from 001 to 127 seconds or minutes can be entered (000 = continuous).
This timer runs only for outputs with logical type “External Bell”.

«
...
52
53
54
55
56
...
»

Summary of Contents for SI120





































































































Reviews:

No comments

Related manuals for SI120

Brand: Hamworthy Pages: 10

Brand: DAV TECH Pages: 10

Brand: Lawler Pages: 4

Brand: Hama Pages: 46

Brand: Galcon Pages: 35

Brand: Fantech Pages: 2

Brand: MacDon Pages: 32

Brand: K&K Pages: 6

Brand: Samson Pages: 8

Brand: Samson Pages: 60

Brand: Samson Pages: 40

CEmarking RCX221

Brand: Yamaha Pages: 468

Brand: K&G GROEP Pages: 27

Brand: CAME Pages: 2

Brand: CalAmp Pages: 13

Brand: Parker Pages: 38

Brand: Parker Pages: 2

Brand: Maximum Controls Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands