Siemens SI120 Configuration Manual Download Page 45 | Manualshive

Page: 45 / 100

background image

Outputs

45

Siemens Building Technologies

Fire Safety & Security Products

07.2009

8.2.5 Strobe

Strobe Light

This output is activated in the event of the following states when the partition parameters are preset.

Partition mode:

Unset

Part set

Full set

Effects on the following events when the below partition parameter are preset:

1

X

Tamper

alarm

1

X

Burglar

alarm

X X X Panic

alarm

9

9

Radio unset (1 seconds)

9

Radio full set (3 seconds)

9

Radio forced full set (6 x 0.5 seconds)

Partition parameters:
X =

Triggering is

always activated regardless of the set state.

2 =

Triggering only "When Full Set" in the partition parameters is chosen.

8 =

Triggering only if "By Fire" in the partition parameter is chosen.

()= Activation of “Duration” (one time per partition) is defined in the menu partition.

8.2.6

Safety Bell if Transmission failure

External Bell on Trans-
mission Fail

This output is activated during full set in the event of a transmission fault in the assigned partition. No activa-
tion takes place during part set or unset.
The maximum activation duration (duration of external bell) is defined in the partition parameters.

8.2.7

Safety Strobe if Transmission failure

Strobe on Transmission
failure

This output is activated during full set in the event of a transmission fault in the assigned partition. No activa-
tion takes place during part set or unset.

8.2.8

Full Set Arming Impossible

Cannot Full Set
(Arming Impossible On
full set:)

This output is activated if the assigned partition can not be switched to full set in following cases
(only if "Set with ...." partition parameter is not enabled):

z

Fault

z

Tamper

z

Burglar Alarm

z

Alarm in Memory

z

Triggered Burglar Inputs without Delay

z

Triggered Panic inputs

z

Triggered Lock Supervision

This output is reset if the cause for the “cannot set” situation is no longer present.

8.2.9

Part Set Arming Impossible

Cannot Part Set
(Arming Impossible on
Part Set)

This output is activated if the assigned partition can not be switched to full set in following cases
(only if "Set with ...." partition parameter is not enabled):

z

Fault

z

Tamper

z

Burglar Alarm

z

Alarm in Memory

z

Triggered Burglar Inputs without Delay

z

Triggered Panic inputs

This output is reset if the cause for the “cannot set” situation is no longer present.

«
...
43
44
45
46
47
...
»

Summary of Contents for SI120





































































































Reviews:

No comments

Related manuals for SI120

Brand: Valve Concepts Pages: 16

7000-2 - Escalade RAID Controller

Brand: 3Ware Pages: 2

Brand: Samson Pages: 48

Brand: Zodiac Pages: 12

Brand: National Instruments Pages: 34

Brand: Zaiput Flow Technologies Pages: 10

Red Atom PETRA01

Brand: Perenio Pages: 24

Brand: GE Pages: 32

SYSVRF AHU 10HP S

Brand: SystemAir Pages: 16

Brand: Zapi Pages: 30

Brand: EasyCare Pages: 26

Brand: ICP DAS USA Pages: 6

Brand: National Instruments Pages: 8

AMBITECH BRAKE-PAK

Brand: TIE Pages: 5

Brand: SUPMEA Pages: 40

Brand: CAME Pages: 32

LiftMaster Security+ 373LM

Brand: Chamberlain Pages: 2

Brand: Gemtek Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands