Siemens SI120 Configuration Manual Download Page 27

Page: 27 / 100

Inputs

Siemens Building Technologies

Fire Safety & Security Products

07.2009

6.3.20 Fire

Fire Alarm

This input will be needed, if a fire warning detector is connected. Shortcut will be detected as an alarm,
4,7 k

= Line OK; broken wire = signaled not as a tamper but as a fault. Acts on the fire bells regardless

of the setting. The burglar alarm bells can also be activated.

NOTE

Therefore the physical input type must be set to „fire detector“.

Partition mode:

Unset

Part set

Full set

Effects on the following outputs when the below partition parameters are preset:

1 1 1 External

bell

2 2 2 Internal

bell

X X X Fire

alarm

X X X Alarm

memory

5 5 5 Buzzer
X X X Fire

transmission

line

Transmission line input

Partition parameters:
X =

Triggering regardless of the partition mode.

1 =

Triggering only if the external bell “When Part Set” in the partition parameter is chosen.

2 =

Triggering only if the internal bell “When Full Set” in the partition parameter is chosen.

5 =

Triggering only if “Buzzer On” in the keypad parameter is chosen.

IMPORTANT

The fire zones and its connected fire detectors are only used as fire warning
devices. The intrusion control unit is not replacing a fire alarm system.

6.3.21 Tamper

Tamper Alarm

Direct triggering of a Tamper in assigned partition.

Partition mode:

Unset

Part set

Full set

Effects on the following outputs when the below partition parameters are preset:

1 X

External

bell

X X 2 Internal

bell

1 X

Strobe

light

Cannot full set

Cannot part set

X X X Alarm

memory

Block lock not released

5 5 5 Buzzer
X

Transmission line tamper

Transmission line input

Partition parameters:
X =

Triggering regardless of the partition mode.

1 =

Triggering only if the external bell “When Part Set” in the partition parameter is chosen.

2 =

Triggering only if the internal bell “When Full Set” in the partition parameter is chosen.

5 =

Triggering only if “Buzzer On” in the keypad parameter is chosen.

Summary of Contents for SI120





































































































Search results

Summary of Contents for SI120

Reviews:

Related manuals for SI120

Brands by name

Popular brands

Siemens SI120, Configuration Manual

Search results

Summary of Contents for SI120

Reviews:

Related manuals for SI120

Brands by name

Popular brands