Siemens SI120 Configuration Manual Download Page 77 | Manualshive

Page: 77 / 100

background image

Service

77

Siemens Building Technologies

Fire Safety & Security Products

07.2009

14 Service

The Service is used to follow up an intervention by an installer or a service pro-
vider. Two Services destinations can be programmed to receive the events. (Syl-
com service station / Pager)

1

2

1

An indicator for a recent service call is the red point next to the tool symbol

2

Every service call feeds the “Service” log with the last 10 events from the Sintony panel.

NOTE

Logging the events, the Sylcom must run on the Service PC and stay on “standby” -> (see Modem
Manager)

[TM65 ]Service trans-
mission

The last 10 events can be transmitted to service station 1 or 2 after an alarm. This transmission can be made
directly after an alarm or not until after unsetting.
This parameter defines this global for both service numbers.

z

ALR = Transmission after alarm,

z

UNS = Transmission only after unset.

[TM63] Service 1

z

Sylcom access

z

Telephone number

z

Customer number (complete system)

[TM64] Service 2

F9

z

Telephone number

z

Protocol ( Sylcom/ TAMTAM / TATOO / KOBBY / Siren Tones / GSM SMS

since A8

)

z

Customer number (complete system)

Service 1 & 2 is used for the up/download functions and for transmitting the last 10 events of the log if a transmission line is triggered.
The modem monitoring in Sylcom must be activated to enable reception.

«
...
75
76
77
78
79
...
»

Summary of Contents for SI120





































































































Reviews:

No comments

Related manuals for SI120

Brand: Panasonic Pages: 15

Brand: Panasonic Pages: 42

Brand: Aaeon Pages: 76

Brand: Daikin Pages: 2

Brand: Daikin Pages: 12

Brand: Daikin Pages: 12

Brand: Daikin Pages: 46

Brand: Daikin Pages: 21

Brand: Daikin Pages: 20

Brand: Parker Pages: 28

Brand: Kärcher Pages: 4

Brand: L-Acoustics Pages: 24

Brand: L-Acoustics Pages: 21

Brand: M&S Systems Pages: 4

Z3-DM8107-SDI-RPS

Brand: Z3 Technology Pages: 73

Brand: Z-Wave Pages: 14

Brand: Z-Wave.Me Pages: 4

Brand: Abocom Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands