Siemens SI120 Configuration Manual Download Page 29

Page: 29 / 100

Inputs

Siemens Building Technologies

Fire Safety & Security Products

07.2009

6.3.24 BA Full Set only

Burglar Alarm Full Set only

Brief description: BA external; internal inactive
On part set: No triggering in the assigned partition.
On full set: Direct triggering in the assigned partition.

Partition mode:

Unset

Part set

Full set

Effects on the following outputs when the below partition parameters are preset:

External

bell

Strobe

light

Cannot full set

Alarm in memory

Block lock not released

5 Buzzer

Burglar alarm system transmission line

Burglar alarm partition transmission line

Transmission line input

Partition parameters:
X =

Triggering regardless of the partition mode.

5 =

Triggering only if “Buzzer On” in the keypad parameter is chosen.

6.3.25 BA Full or Part Set

Burglar Alarm Full/Part Set

Brief description: BA external; internal
Direct triggering on Part and Full set in the assigned partition.

Partition mode:

Unset

Part set

Full set

Effects on the following outputs when the below partition parameters are preset:

1 X

External

bell

2 Internal

bell

1 X

Strobe

light

Cannot full set

Cannot part set

Alarm in memory

Block lock not released

5 5 Buzzer

Burglar alarm system transmission line

Burglar alarm partition transmission line

Transmission line input

Partition parameters:
X =

Triggering regardless of the partition mode.

1 =

Triggering only if the external bell “When Part Set” in the partition parameter is chosen.

2 =

Triggering only if the internal bell “When Full Set” in the partition parameter is chosen.

3 =

Triggering only if "transmission" parameter is chosen.

5 =

Triggering only if “Buzzer On” in the keypad parameter is chosen.

Summary of Contents for SI120





































































































Search results

Summary of Contents for SI120

Reviews:

Related manuals for SI120

Brands by name

Popular brands

Siemens SI120, Configuration Manual

Search results

Summary of Contents for SI120

Reviews:

Related manuals for SI120

Brands by name

Popular brands