Siemens SI120 Configuration Manual Download Page 57

Page: 57 / 100

Partitions

Siemens Building Technologies

Fire Safety & Security Products

07.2009

9.12 Forced

Set

Forced Set

This parameter defines whether or not the partition permits forced setting. Forced setting means that trig-
gered input lines are automatically bypassed when assigned partition is set.
However, all of the following conditions must be fulfilled:

Triggered input lines must be defined as capable of being bypassed.

Not more than the defined number of inputs (50% or ONE defined by parameter "bypass mode") may be

bypassed.

When setting with a PIN the user must have forced setting authority (setting via an input is equivalent to

forced setting)
The following four options are available for this parameter.
0 = No

Authority

Forced setting is not possible.

1 = Until

Unset

Forced setting is possible whereby the bypassed lines remain bypassed until assigned partition is
unset.

2 = Until Input quiescent state

Forced setting is possible whereby the bypassed lines remain bypassed until assigned partition is
unset or the bypassed line is in quiescent state.

3 = Forced

Set

Forced setting possible whereby the bypassed lines immediately trigger an alarm when forced setting
takes place.

9.13 Transmission

9.13.1 Burglar Alarm/P. Set

Part Set Transmission of
Burglar Alarm

This parameter defines whether or not transmission is enabled on

part set or unset

in the event of a burglar

alarm.
B = Enabled
- = Disabled

9.13.2 Tamper Alarm/P. Set

Part Set Transmission of
Tamper Alarm

This parameter defines whether or not transmission is enabled on

part set or unset

in the event of a tamper

alarm.
T = Enabled
- = Disabled

Summary of Contents for SI120





































































































Search results

Summary of Contents for SI120

Reviews:

Related manuals for SI120

Brands by name

Popular brands

Siemens SI120, Configuration Manual

Search results

Summary of Contents for SI120

Reviews:

Related manuals for SI120

Brands by name

Popular brands