Siemens SI120 Configuration Manual Download Page 78 | Manualshive

Page: 78 / 100

background image

Service

78

Siemens Building Technologies

Fire Safety & Security Products

07.2009

14.1 Service 1 & 2

Up/Download
->only Service 1

If an up/download with callback is carried out. In this case Sintony calls back to the number programmed
under Service 1.

Pager transmission
->only Service 2

When a pager protocol is chosen, alarms can be transmitted to a pager.

Transmit log
-> Service 1 & 2

If after an alarm the last 10 events are to be transmitted. By programming a transmission line on Service 1
&2 (engineer menu "Lines Telecom Option" (TM66) "Service 1&2" parameter), the last 10 events of the
engineer log is transmitted to Service 1 when they are triggered.
Two types of transmission can be chosen for this purpose (engineer menu "Other Telecom Options" [TM65]
"Service transmission" parameter), as follows:

z

Directly after triggering,

z

Not until after the relevant partition has been switched to unset.

Modem monitoring
->Service 1 & 2

For these function to be able to be used, a Sylcom software in modem monitoring mode must be running at
the service number.

Sylcom Access

Defines which communication device will be used to do remote connection from Sylcom to the control panel.

z

VIA SML51/61

z

VIA SMN42/SMN43

NOTE

With the A8 version it is only possible to have an SMN42 or an SML51/SML61.
With the A9 version it is possible to have an SMN42 and an SML51 (connection to Sylcom), but only
one connection is possible at a time.

14.2 Telephone

telephone numbers
->Service 1& 2

Programming the telephone numbers with the keypad, follow this description:
When changing the number all the digits not required must be overwritten with F.
If no telephone number is used, all the characters must be F.
The first character must always be a B (wait for dialing tone) or C (occupy line and wait 2 seconds). If neces-
sary, several Cs can be used.

z

F = key

@

z

B = part set key

z

C = full set key

z

B and C can also be entered by pressing

@

key several times.

Example

:

If the Control panel is connected directly to the public telephone network B94873321 must be entered to
obtain the number 94.87.33.21. If, however, the Control panel is connected to the internal exchange call
number "0" through a private automatic branch exchange, C0B94873321 must be entered to obtain the
number 94.87.33.21.

14.2.1 Site

Number

Site Number
-> Service 1& 2

The site number of the system (8-digit) must be entered here.
This number must match with the customer number of the system (Service 1 customer number) in the Syl-
com customer file.

«
...
76
77
78
79
80
...
»

Summary of Contents for SI120





































































































Reviews:

No comments

Related manuals for SI120

Brand: unicore Pages: 25

Brand: unicore Pages: 24

Brand: Samsung Pages: 32

Brand: Rain Bird Pages: 20

Brand: Uniden Pages: 28

Brand: UniFocus Pages: 23

Brand: UniFocus Pages: 6

Brand: YASKAWA Pages: 340

Brand: TEL Pages: 26

Brand: Vimar Pages: 32

Brand: Aqua Lung Pages: 24

Brand: Rare Waves Pages: 18

GA INDUSTRIES Figures 251-D

Brand: Vag Pages: 6

Brand: Trikdis Pages: 7

Ramping and Profiling Microprocessor-Based Control SERIES 1500

Brand: Watlow Pages: 90

Brand: Parallax Pages: 7

Job Aid+ 1442981G8C

Brand: ADTRAN Pages: 2

Brand: CLA-VAL Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands