Siemens SI120 Configuration Manual Download Page 55 | Manualshive

Page: 55 / 100

background image

Partitions

55

Siemens Building Technologies

Fire Safety & Security Products

07.2009

9.4.3 By

Fire

External Bell / Fire

This parameter defines whether or not the external bell is enabled in the event of a fire warning alarm (alter-
nating 2 seconds ON, 1 second OFF).
Yes = Enabled (Activation time defined by External Bell Dureation (not fire bell duration)
No =

Disabled

9.4.4 RF

Confirm

External Bell on RF

If this parameter is activated, the external bell indicates the arming confirmation if partition is set or unset by
radio remote control. Radio-setting is indicated with 2 short pulses, unsetting with only one pulse.
Yes = Enabled

No =

Disabled

9.5 Internal

Bell

9.5.1 When

Full

Set

Internal Bell Mode

This parameter defines whether or not the internal bell is enabled in the event of a burglar alarm On full set:.
This parameter also acts on the strobe light output.
Yes = Enabled

No =

Disabled

9.5.2 Duration

Internal Bell Duration

This parameter defines the maximum triggering time of the internal bell output in the event of an alarm.
Times from 000 to 127 seconds or minutes can be entered (000 continuous).
This timer runs only for outputs with logical type “Internal Bell”.

9.5.3 By

Fire

Internal Bell/Fire

This parameter defines whether or not the external bell is enabled in the event of a fire warning alarm (2
seconds ON, 1 second OFF).
Yes = Enabled. Activation time defined by Internal Bell Dureation (not fire bell duration)
No =

Disabled

9.6 Fire

Bell

Fire Bell Mode

This parameter defines whether or not the fire warning bell is continuously or intermittently enabled in the
event of a fire warning alarm:
F = Fixed

(continuous)

I = Intermittent (2 seconds ON, 1 second OFF).
.

IMPORTANT

The fire zones and its connected fire detectors are only used as fire warning
devices. The intrusion control unit is not replacing a fire alarm system

«
...
53
54
55
56
57
...
»

Summary of Contents for SI120





































































































Reviews:

No comments

Related manuals for SI120

Brand: Zetkama Pages: 6

Brand: Facility Explorer Pages: 4

Brand: Hansen Pages: 4

Brand: Bard Pages: 8

Brand: Bardiani Valvole Pages: 35

SmartSwitch 6000

Brand: Cabletron Systems Pages: 76

Brand: Samson Pages: 52

Brand: Samson Pages: 32

Brand: Danfoss Pages: 59

Brand: jablotron Pages: 2

Brand: ZIGBEE Pages: 5

Brand: MAKOT Pages: 6

Brand: X Rocker Pages: 38

Brand: YASKAWA Pages: 121

Brand: YASKAWA Pages: 17

Brand: YASKAWA Pages: 58

Brand: YASKAWA Pages: 30

Brand: Zamel Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands