manualshive.com logo in svg

Siemens SI120, Configuration Manual

Share
Download
Siemens SI120 Configuration Manual Download Page 62

Keypads 

62 

Siemens Building Technologies

 

 

Fire Safety & Security Products 

 

07.2009

 
 

F: Fire 

The buzzer is activated on a fire alarm (alternating, 2 seconds on and 1 second off) 

10.5 RF 

Control 

 

RF Control 

The buzzer is activated for a short buzzes when the system will be full set by RF remote control. 

10.6 Quick 

Set 

 

Digit Part Set 

This parameter permits the enabling of the part set key for direct setting for the default partition of this key-
pad. 
On direct part setting the basic partition is part set without having to enter a PIN. The basic partition is di-
rectly part set by pressing the "

Part Set

" key twice. 

Digit Full Set 

This parameter permits the full set key to be enabled for direct setting for the basic partition. 
On direct full setting the basic partition is full set without having to enter a PIN. The basic partition is set to 
full set by pressing the "

Full Set

" key twice. 

Summary of Contents for SI120





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands