Polycom VIEWSTATION EX User Manual Download Page 34 | Manualshive

Page: 34 / 356

background image

ViewStation EX User Guide

32

www.polycom.com

Integrated Cameras

Sony EVI-10 Camera

The ViewStation EX system supports the Sony EVI-10 camera. This
camera has a built-in wide-angle lens and has a new form factor.

Figure 2-1.

ViewStation EX with Sony EVI-10 Camera

Caution

Attaching a third-party vendor wide-angle lens will cause damage
that is not covered by your product warranty. Third-party lenses
will rub against the system’s enclosure when the camera is reset.

Note

The camera is controlled with the remote control that is shipped
with the system. Manually adjusting the camera can damage the
unit.

NT-1 Device

An ISDN network termination (NT-1) device may be required
between your ISDN line and the system. If your system is not
connected to an internal switchboard, such as a PBX, it may require
an ISDN termination resistor to be installed.

«
...
32
33
34
35
36
...
»

Summary of Contents for VIEWSTATION EX





































































































































































































































































































































































Reviews:

No comments

Related manuals for VIEWSTATION EX

Brand: SAI Pages: 16

Brand: Eagle Copters Pages: 11

Brand: Measurement Computing Pages: 32

SAE 07.2 Series

Brand: AUMA Pages: 116

Brand: TANDBERG Pages: 65

Brand: Discount Car Stereo Pages: 4

Brand: Daewoo Pages: 44

Brand: Automated Logic Pages: 3

Brand: Gamma Vacuum Pages: 43

Zynq UltraScale+

Brand: Xilinx Pages: 86

Brand: Madas Pages: 40

Brand: Trevi Pages: 46

Brand: Midland Pages: 24

Brand: CDK ELECTRONICS Pages: 22

Brand: BFT Pages: 68

Brand: HandyTrac Pages: 20

Brand: Raven Pages: 48

Brand: AAD Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands