Polycom VIEWSTATION EX User Manual Download Page 328

Page: 328 / 356

ViewStation EX User Guide

326

www.polycom.com

Digital Tabletop
Microphone

360

voice pick-up, unidirectional performance

Automatic room noise reduction

Gated mixer built into microphone

3 Hyper-cardiod microphones in each microphone pod

Mute button on each microphone pod

Includes 1 microphone pod

Can be mounted to ceiling or walls

Audio Inputs (4
Inputs)

RJ-9 to microphone (daisy chain up to 2 microphone pods)

2 x RCA / Phono line level (VCR)

1 x RCA / Phono line level (Mixer/Auxiliary)

Audio Outputs (4
Outputs)

2 x RCA / Phono line level (main audio)

2 x RCA / Phono line level (VCR)

Frame Rates

(point-to-point)

15 fps - 30 fps

Intelligently selects frame rate for best video performance

TV-quality letterbox 60/50 fields video for NTSC/PAL at 512 kbps and above

Optional Embedded
MPPlus

Supports mixed combinations of IP, ISDN, and analog telephone calls

Supports IP telephones

Supports normal analog telephones

Automatic IP and ISDN downspeeding

Dial-in and dial-out during multipoint calls

Continuous presence or voice switched

Automatic multipoint presentation modes to automatically switch between presenter
and continuous presence modes

Chair control from endpoints or host system on IP

Chair control from endpoints or host system on ISDN

Embedded multipoint for 5 sites (4 IP/ISDN sites + 1 POTS audio)

Cascade up to 14 sites (10 IP/ISDN sites + 4 POTS audio)

Mixed network cascading

Password protection for incoming calls

Supports Content dual streams from any endpoint (not just host site)

Summary of Contents for VIEWSTATION EX





































































































































































































































































































































































Search results

Summary of Contents for VIEWSTATION EX

Reviews:

Related manuals for VIEWSTATION EX

Brands by name

Popular brands

Polycom VIEWSTATION EX, User Manual

Search results

Summary of Contents for VIEWSTATION EX

Reviews:

Related manuals for VIEWSTATION EX

Brands by name

Popular brands