Polycom VIEWSTATION EX User Manual Download Page 140 | Manualshive

Page: 140 / 356

background image

ViewStation EX User Guide

138

www.polycom.com

Configuring SNMP Preferences

SNMP (Simple Network Management Protocol) is a set of protocols
used to manage complex networks. SNMP tells the network if a
device or operation is functioning properly. The ViewStation EX
sends SNMP reports on the following:

❑

Low battery power in the remote control.

❑

System is being powered on after a long time powered off.

❑

Authentication failure—someone is attempting to log in as an
administrator with the wrong password.

❑

Authentication success—someone has logged on successfully as
an administrator.

❑

Call failed for reason other than a busy line.

❑

A user has asked for help from the Technical Assistance Center.

❑

A system is in a telephone or video call.

❑

A telephone or video call has disconnected.

To access the SNMP Setup screen:

Select System Info > Admin Setup > LAN/H.323 > SNMP. The
SNMP Setup

screen appears.

Figure 4-28.

SNMP Setup Screen

«
...
138
139
140
141
142
...
»

Summary of Contents for VIEWSTATION EX





































































































































































































































































































































































Reviews:

No comments

Related manuals for VIEWSTATION EX

Brand: S&S Northern Pages: 12

TracPhone V3 LNB

Brand: KVH Industries Pages: 4

Brand: Legacy Pages: 25

VidyoConference

Brand: Vidyo Pages: 2

Brand: Panasonic Pages: 24

Brand: Chamberlain Pages: 28

OPTISOUND OPTIFORD6-V8

Brand: Vibe Pages: 4

Brand: Raven Pages: 60

ATC TRAILER CONTROL

Brand: AL-KO Pages: 112

Brand: Akura Pages: 18

Brand: Moxa Technologies Pages: 12

Brand: Hamilton Air Pages: 3

Brand: Victron energy Pages: 12

Brand: Daikin Pages: 376

Brand: Aiwa Pages: 73

Brand: Sapho Pages: 4

Brand: Gestton Pages: 14

Brand: HWH Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands