Polycom VIEWSTATION EX User Manual Download Page 73

Page: 73 / 356

Chapter 3 - Initial System Setup

the Broadcast Mode screen, refer to

Setting up Satellite (H.331)

Broadcast Mode on page 105

Setting Advanced Dialing Preferences

If you enabled RS-366 Dialing, the dialing prefixes and suffixes are
set for calls from the system on the Advanced Dialing screen.

The Advanced Dialing screen lets you select the Calling Profile
associated with dialing through a DCE.

Figure 3-8.

Advanced Dialing Screen

Calling profiles for several manufacturers are included in your
system.

Summary of Contents for VIEWSTATION EX





































































































































































































































































































































































Search results

Summary of Contents for VIEWSTATION EX

Reviews:

Related manuals for VIEWSTATION EX

Brands by name

Popular brands

Polycom VIEWSTATION EX, User Manual

Search results

Summary of Contents for VIEWSTATION EX

Reviews:

Related manuals for VIEWSTATION EX

Brands by name

Popular brands