Panasonic LX-TD500 Programming Manual Download Page 252

Page: 252 / 388

Features

252

Programming Guide

Parameter

Max. Entry

Default

(Display only)

Value Range

0-1000

Description/Function

Displays the maximum number of Speed Dialing codes allocated to
the tenant.

Reference

• 1.3 System Features (F/G)

– Tenant Service

• 2.2

Tenant (P/G)

Parameter

Current Registration

Default

(Display only)

Value Range

0-1000

Description/Function

Displays the total number of Speed Dialing codes which are
already programmed.

Reference

None

Parameter

Name

Default

Blank

Value Range

Up to 10 characters consisting of 0-9, A-Z, a-z or the following
marks: ! # $ % ( ) + , - / : ; < = > ? @ &.

Description/Function

Specifies the name for each speed dial code.

Notes

•

The stored name is shown on a large display PT, such as KX-
T7235 / KX-T7436, when dialing System Speed Dialing
number.

•

Both "Name" and "Number" should be stored in pairs for
each System Speed Dialing No. Otherwise "Name" is not
shown on a large display PT.

Reference

• 4.5.8 KX-T7235 Display Features - Call Directory (U/M)
• 4.5.11 KX-T7431 / KX-T7433 / KX-T7436 Display Features -
Call Directory (U/M)

Summary of Contents for LX-TD500





































































































































































































































































































































































































Search results

Summary of Contents for LX-TD500

Reviews:

Related manuals for LX-TD500

Brands by name

Popular brands

Panasonic LX-TD500, Programming Manual

Search results

Summary of Contents for LX-TD500

Reviews:

Related manuals for LX-TD500

Brands by name

Popular brands