Panasonic LX-TD500 Programming Manual Download Page 130 | Manualshive

Page: 130 / 388

background image

System

130

Programming Guide

Parameter

12. Automatic adjustment of the clock using

Caller ID information

Default

No

Value Range

1.

Yes

2.

No

Description/Function

Enables or disables the automatic adjustment of the clock by Caller
ID information once a day.

Reference

• 1.5 Attended Features (F/G)

– Caller ID Service

Parameter

13. DISA prolong operation

Default

No limit

Value Range

1.

Limited (10 times)

2.

No limit

Description/Function

Specifies the number of times that the DISA caller can prolong the
duration of DISA CO-to-CO line call.

Reference

• 1.5 Attended Features (F/G)

– Direct Inward System Access (DISA)

Parameter

14. Dialing "*" in DISA CO-to-CO talking

Default

Disconnect and make a new call

Value Range

1.

Disconnect and make a new call

2.

Send out Dial " "

Description/Function

The " " key can be entered during a DISA CO-to-CO line call. The
action taken by the system depends upon this setting.
If "Disconnect and make a new call" is selected, then the system
will disconnect the current call and prepare for a new call.
Otherwise, the will be transmitted down the line to the other
party.

Reference

• 1.5 Attended Features (F/G)

– Direct Inward System Access (DISA)

«
...
128
129
130
131
132
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

Brand: Bad Boy Pages: 132

Brand: Arctic Cat Pages: 68

Brand: Craftsman Pages: 56

Brand: Suzuki Pages: 477

Hawkeye 2X4 2007

Brand: Polaris Pages: 141

Brand: Polaris Pages: 133

RANGER 500 2017

Brand: Polaris Pages: 574

2010 Scrambler 4X4

Brand: Polaris Pages: 133

Sportsman BIG BOSS 6X6 800 EFI

Brand: Polaris Pages: 100

2012 Prowler XT

Brand: Arctic Cat Pages: 64

1000 TRV LIMITED

Brand: Arctic Cat Pages: 84

Brand: Blaw-Knox Pages: 118

Brand: PROALL Pages: 59

Brand: Egholm Pages: 16

2009 Ranger RZR 800 EFI

Brand: Polaris Pages: 332

Brand: Jianshe Pages: 52

IBT 4000 Series

Brand: IBEA Pages: 56

Brand: Arctic Cat Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands