Panasonic LX-TD500 Programming Manual Download Page 55 | Manualshive

Page: 55 / 388

background image

Configuration

Programming Guide

55

Parameter

Attribute

Default

TEL

Value Range

1.

TEL

2.

DSS

3.

VPS (DPT)

Description/Function

Specifies the attribute of the terminal which is to be connected to
the extension port.

1.

TEL:
Select this option when you connect a telephone set to the
extension port.

2.

DSS:
Select this option when you connect a DSS Console to the
extension port.

3.

VPS (DPT):
Select this option when a port of Panasonic Voice Processing
System (one that supports DPT Integration) is connected to the
extension port.

Notes

•

"DPT integration (except TVS300)" does not function unless
the VPS is connected to a DLC or DHLC card whose LPR
Version (ROM Version) is 1 or later.

•

"DPT integration (TVS300 only)" does not function unless it
is connected to a DLC or DHLC card whose LPR Version
(ROM Version) is 2 or later.

•

You can confirm the LPR Version (ROM Version) of the
DLC and the DHLC card in "Card Properties" Screen for
each card. Please refer to "LPR Version" parameter in
Section "1.2.3 Card Properties (DHLC/ESLC/DLC)."

•

There is a limit of 8 VPS (DPT) ports per card.

•

There is a limit of 16 VPS (DPT) ports per shelf.

Reference

• 1.5

VPS (DPT) Port Assignment (P/G)

• 4.3

Extension Line (P/G)

• 4.4

DSS Console (P/G)

«
...
53
54
55
56
57
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

Brand: ShoreLand'r Pages: 11

QUAD - PART LIST 2007

Brand: GAS GAS Pages: 77

Brand: Toro Pages: 20

BOSS RT FATBOY 1026RT RR

Brand: Meyer Pages: 44

Onslaught 550 EFI 4X4 EPS

Brand: Bad Boy Pages: 67

Transporta CCT 5221

Brand: Ifor Williams Trailers Pages: 45

Stand-Up GO! Series

Brand: Kendon Pages: 40

Sportsman 850 2021

Brand: Polaris Pages: 180

Brand: KTM Pages: 247

Brand: Yamaha Pages: 52

Brand: Range Road Pages: 6

Brand: SVA Pages: 15

Brand: Twister Pages: 66

Brand: Intimidator Pages: 74

Brand: Intimidator Pages: 92

Brand: FORS MW Pages: 15

Brand: ELK Golf Pages: 40

Brand: BERG Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands