manualshive.com logo in svg

Panasonic LX-TD500, Programming Manual

The Panasonic LX-TD500 Programming Manual is an essential resource for users looking to maximize the features and functionality of their LX-TD500 unit. Easily downloadable and completely free, this comprehensive manual is available for download from our website, ensuring effortless access to important programming instructions and guidelines.

Share
Download
background image

Line

Programming Guide

205

Parameter

Destination—Day/Night/Lunch/Break

Default

Day, Night: 1001, Lunch, Break: Blank

Value Range

3-4 digits consisting of 0-9

Description/Function

Specifies the destination for the trunk line whose "Incoming Type" 
is set to "DIL." 
The following numbers can be assigned as the destination: 
Extension numbers, FDNs.

(Assignable only when "DIL" is specified in "Incoming Type" 
programming.)

Note

•

When "Incoming Type" of the ISDN trunk line is set to "DID 
(ISDN)," you can specify the destination DN/FDN as 
"Destination." In this case, the destination DN/FDN 
specified by this setting is available, not that specified in "9-
1 DID Dial Registration" screen.

Reference

• 1.5 Attended Features (F/G)

– Direct In Lines (DIL)

• 2.3 ISDN Attended Features (F/G)

– Direct Inward Dialing (DID)

Parameter

Subscriber

Default

Blank

Value Range

Up to 16 digits consisting of 0-9,   or #

Description/Function

Specifies the number which is used as the CLIP (Calling Line 
Identification Presentation) number.

Notes

•

When an extension user makes an outside call using an ISDN 
BRI line, the number stored in "DN" <Section "1.2.9 Card 
Properties (BRI) – SPID/DN" in the Programming Guide> is 
displayed on the telephone of the other party as the CLIP 
number. 

•

Specify the registered Central Office calling number for 
correct operation of CLIP.

Reference

• 2.2 ISDN Originating Features (F/G)

– Calling Line Identification Presentation (CLIP)

• 4.3.19 Calling Line Identification Presentation (CLIP) (U/M)

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

Ezgo WorkHorse ST 480 Technician'S Repair And Service Manual preview
WorkHorse ST 480
Brand: Ezgo Pages: 164
Landoll 345D Operator'S Manual preview
345D
Brand: Landoll Pages: 64
MANCO ATV-50 Service Manual preview
ATV-50
Brand: MANCO Pages: 16
BOMBARDIER DS650 X 2005 Operator'S Manual preview
DS650 X 2005
Brand: BOMBARDIER Pages: 129
LAMAX eFalcon ATV50M User Manual preview
eFalcon ATV50M
Brand: LAMAX Pages: 150
Etnyre PAVER SPECIAL RPS Series Parts And Operation Manual preview
PAVER SPECIAL RPS Series
Brand: Etnyre Pages: 61
Evinrude Trailblazer E2020 Operation Manual preview
Trailblazer E2020
Brand: Evinrude Pages: 14
Can-Am DS 450 EFI X mx Operator'S Manual preview
DS 450 EFI X mx
Brand: Can-Am Pages: 156
Baja motorsports Extreme 150 Owner'S Manual preview
Extreme 150
Brand: Baja motorsports Pages: 73
Dometic PRO TRIM PT1000-2 Installation Manual preview
PRO TRIM PT1000-2
Brand: Dometic Pages: 16
cectek Kingcobra Manual preview
Kingcobra
Brand: cectek Pages: 125
Columbia Summit Owner'S And Operator'S Manual preview
Summit
Brand: Columbia Pages: 29
Columbia P5 Owner'S And Operator'S Manual preview
P5
Brand: Columbia Pages: 30
Walinga Chem-Veyor 2614D Operator'S & Parts Manual preview
Chem-Veyor 2614D
Brand: Walinga Pages: 28
E-Z-GO TXT 48V Repair And Service Manual preview
TXT 48V
Brand: E-Z-GO Pages: 192
Baja motorsports WD400U-2 Owner'S Manual preview
WD400U-2
Brand: Baja motorsports Pages: 89
Landoll 825D Series Operator'S Manual preview
825D Series
Brand: Landoll Pages: 80
Landoll 900D Series Operator'S Manual preview
900D Series
Brand: Landoll Pages: 82

Brands by name

Popular brands

Load more brands