Panasonic LX-TD500 Programming Manual Download Page 71 | Manualshive

Page: 71 / 388

background image

Configuration

Programming Guide

71

Parameter

Group No.

Default

1

Value Range

1-48 or 1-128

Description/Function

Type: CO
Specifies the Trunk Group (1-48) to which the BRI port is assigned.
Type: EXT
Specifies the Extension Group (1-128) to which the BRI port is
assigned.

Reference

• 1.3 System Features (F/G)

– Extension Group
– Trunk Group

• 3.2

Trunk Group (P/G)

• 3.3

Extension Group (P/G)

Parameter

Status

Default

—

Value Range

1.

INS

2.

OUS

3.

FAULT

Description/Function

Specifies the operating status of the BRI port.

1.

INS: The BRI port is In-Service.

2.

OUS: The BRI port is Out-of-Service.

3.

FAULT: The BRI port is defective (hardware).
In this case, the LED indicator on the BRI card will light.

Reference

None

Parameter

DN Refer

Default

—

Value Range

—

Description/Function

Displays the list of DNs/FDNs which are already assigned to the
extensions / system resources.

Reference

None

«
...
69
70
71
72
73
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

Buggy Raider mini 90D

Brand: Dazon Pages: 60

Brand: Baja motorsports Pages: 73

Sportsman 800 Big Boss

Brand: Polaris Pages: 143

Brand: Jayco Pages: 104

Brand: Humbaur Pages: 36

Brand: Yamaha Pages: 142

Brand: Range Road Pages: 6

Brand: Bosski Pages: 12

AUTOMIZER HELPING-HAND

Brand: Labrie Pages: 118

Brand: Opus Pages: 21

Trail-Blazer TB-6000

Brand: J&M Pages: 30

Brand: HERCHEE Pages: 34

Brand: CMi Pages: 4

FourTrax Rancher TRX420FM1 2020

Brand: Honda Pages: 273

Brand: KYMCO Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands