Panasonic LX-TD500 Programming Manual Download Page 59 | Manualshive

Page: 59 / 388

background image

Configuration

Programming Guide

59

1.5

VPS (DPT) Port Assignment

Used to assign parameters for VPS (DPT) ports. Up to eight Panasonic Voice Processing
Systems (VPSs) can be connected to the system.

How to set up a TVS

1. Assignment of the card which will be connected to the VPS System.

•

When you use a new DLC / DHLC card and set up the TVS to the PBX:

Assign the card type of the slot to be installed to "DLC" or "DHLC" card and change the
card status to "INS (In-Service)" in "1-1 Slot Assignment" screen.
Then, see the information of "Card Properties" and confirm that the software version of
the card shows more than "1."

•

When you connect the TVS to the existing DLC / DHLC: Go to step 2.

2. Assignment of the port which will be connected to the VPS System.

Change the attribute of the port to be connected to the TVS to "VPS (DPT)" in "1-3 Extension
Port Assignment" screen. When the attribute of the port is changed to "VPS (DPT)," the
parameters except "Attribute" will disappear and the directory number will be purged.

3. Assignment of VPS card and its model.

Select the corresponding equipment number in "TVS No." menu, the card (DLC / DHLC)
which connects with the TVS in "VPS Card" menu, and the model of TVS in "Type" menu in
"1-4 VPS (DPT) Port Assignment" screen.

«
...
57
58
59
60
61
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

Brand: Hammerhead Off-Road Pages: 105

Brand: Arctic Cat Pages: 174

Brand: Madill Pages: 45

PROWLER 500 2018

Brand: Textron Pages: 60

Outlander X mr Series

Brand: Can-Am Pages: 196

2009 Outlander 500 EFI

Brand: Can-Am Pages: 152

Brand: swaploader Pages: 94

Brand: E-Z-GO Pages: 78

Brand: YTL Pages: 23

DewEze 400 Series

Brand: Harper Pages: 75

Brand: Yamaha Pages: 112

Brand: Yamaha Pages: 398

Grizzly 450 YFM45FGPD

Brand: Yamaha Pages: 172

Brand: Taylor-Dunn Pages: 188

Brand: Taylor-Dunn Pages: 206

Brand: Taylor-Dunn Pages: 260

Brand: Baja Pages: 57

Brand: Baja motorsports Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands